EasyManua.ls Logo

Beko CLEARPOINT Series - User Manual

Beko CLEARPOINT Series
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
EN - english
Instructions for installation and operation
Activated-carbon adsorber without dust filter
CLEARPOINT
®
L 205 – L295 V

Table of Contents

Other manuals for Beko CLEARPOINT Series

Preview: Operating Manual
Operating Manual16 pages

Questions and Answers

  • M
    Ms. Alejandra Bowen DDSAug 5, 2025
    What to do if the container pressure is too low in Beko Air Compressor?
    • V
      vmckeeAug 5, 2025
      If the container pressure or operating pressure is too low in your Beko Air Compressor, start by checking the pressure drop via the inlet filter and replace the filter element if required. Ensure the compressed-air system upstream of the activated-carbon adsorber is not pressureless and eliminate any faults. Also, inspect for wear debris in the system, which may clog the compressed-air distributor or filter elements. Replace the dust filter element and the activated carbon. Clean the compressed-air distributor and verify the operating conditions, such as pulsation and volume flow.
  • C
    Casey TrevinoAug 12, 2025
    How to clean oil-contaminated circuit sections in Beko Air Compressor?
    • C
      Christopher HammondAug 12, 2025
      If the residual oil content is too high in your Beko Air Compressor, and you suspect oil-contaminated circuit sections between the activated-carbon adsorber and the measuring point, clean the pipe section or install a new pipe section.
  • F
    fwallaceAug 19, 2025
    What to do if condensate drainage upstream of the activated-carbon adsorber does not work in Beko Air Compressor?
    • S
      Susan LynnAug 20, 2025
      If you're experiencing high residual oil content and suspect the condensate drainage upstream of the activated-carbon adsorber is not working in your Beko Air Compressor, check the functioning of the condensate drain (at the inlet filter), and repair or replace it, if required.
  • S
    Sharon SantosOct 27, 2025
    Why is the residual oil content too high in my Beko Air Compressor?
    • B
      ballraymondOct 27, 2025
      High residual oil content in your Beko Air Compressor can be due to several reasons. It could be that the inlet volume flow is too high, in which case you should reduce it. Alternatively, the operating pressure might be too low, so increase it. A high compressed-air temperature at the inlet may also be the cause; try reducing it or installing a precooler. Check if your inlet filter elements are exhausted, and replace them if the pressure difference is too high. Ensure you are using BEKO filters and filter elements in an oil- and grease-free version. Clean any oil-contaminated circuit sections or replace them. Also, verify the condensate drain is functioning correctly and repair or replace it if needed. Finally, the activated carbon might have reached its maximum absorption capacity, requir...

Summary

General Advice and Safety Instructions

Safety Instructions

Covers warnings, pictograms, and signal words for safe operation and maintenance.

Technical Data and Components

Technical Data CLEARPOINT L 205-295 V

Details operational parameters, dimensions, pressure ratings, and construction standards.

Transport and Setup

Transport and Set-up Safety

Details safety precautions for handling, transporting, and setting up the CLEARPOINT® V.

Transport Procedures

Set-up Requirements

Installation

Installation Safety

Covers safety measures and personnel qualifications necessary for performing the installation work.

Minimum Requirements

Installation Examples

Work Steps During Installation

Operation and Startup

Startup Safety and Checks

Covers safety guidelines and crucial checks before the initial startup of the CLEARPOINT® V.

Initial Startup Procedure

Details the step-by-step procedure for the first-time startup of the CLEARPOINT® V.

Troubleshooting and Maintenance

Troubleshooting and Fault Elimination

Provides guidance on identifying and resolving common issues and faults with the CLEARPOINT® V.

Status and Alarm Indications

Maintenance Safety and General Practices

Covers safety precautions and general maintenance practices for the CLEARPOINT® V.

Activated Carbon Replacement

Beko CLEARPOINT Series Specifications

General IconGeneral
CategoryWater Filtration Systems
BrandBeko
Filter TechnologyActivated Carbon Block
Installation TypeUnder Sink
Series NameCLEARPOINT Series
Filter Replacement IndicatorYes
CertificationsNSF/ANSI 42, NSF/ANSI 53
Filter TypeUnder Sink
Operating Pressure30-100 psi
Operating Temperature40-100°F

Related product manuals