What to do if my Beko Washer does not drain water?
If your Beko Washer doesn't drain water, the water drain hose might be clogged or twisted, so you should clean or flatten the hose. Also, the pump filter may be clogged, requiring you to clean it.
Why does my Beko Washer enter standby mode or not take in water?
If the machine enters standby mode after the programme starts or it does not take in water, it could be due to several reasons. The tap might be turned off, so turn on the taps. The water inlet hose might be bent, so flatten the hose. The water inlet filter might be clogged, so clean the filter. The loading door may be open, so close the door. The water connection may be wrong or water may be cut off, so check the water connection. If the water is cut off, press the Start/Pause key after the water has been supplied again to resume the operation from standby mode.
What to do if the Beko WUE 5411 XWW Washer programme cannot be started or selected?
If your Beko Washer programme cannot be started or selected, the washing machine may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be canceled.
Why is my Beko Washer vibrating or making noise?
If your Beko Washer vibrates or makes noise, make sure the machine is standing balanced by adjusting the feet to level it. A hard substance might have entered into the pump filter, so you should clean the pump filter. Ensure that the transportation safety bolts are removed. The laundry quantity in the machine might be too little, so you can add more laundry. The machine might be overloaded with laundry, so take out some of the laundry or distribute the load by hand to balance it. Also, make sure that the machine is not leaning on anything.
Why doesn't my Beko Washer rinse well?
If your Beko Washer does not rinse well, the amount, brand, and storage conditions of the detergent used are inappropriate, so use a detergent appropriate for the washing machine and your laundry and keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures. Detergent is put in the wrong compartment, so if detergent is put in the prewash compartment although the prewash cycle is not selected, the machine can take this detergent during rinsing or softener step. Put the detergent in the correct compartment. The pump filter is clogged, so check the filter. The drain hose is folded, so check the drain hose.
Why is there water leaking from the bottom of my Beko WUE 5411 XWW?
If there is water leaking from the bottom of your Beko washing machine, the water drain hose might be clogged or twisted, so you should clean or flatten the hose. Also, the pump filter may be clogged, requiring you to clean it.
Why doesn't my Beko WUE 5411 XWW Washer switch to spinning step?
If your Beko Washer machine does not switch to the spinning step, there might be an unbalanced load in the machine, so the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum. The machine will also not spin if water is not drained completely, so check the filter and the draining hose. Excessive foam might have occurred and the automatic foam absorption system might have been activated due to too much detergent usage, so use the recommended amount of detergent.
Why doesn't my Beko Washer start after closing the door?
If your Beko Washer program does not start after closing the door, it may be because the Start / Pause / Cancel button was not pressed, so press the Start / Pause / Cancel button. It may also be difficult to close the loading door in case of excessive loading, so reduce the amount of laundry and make sure that the loading door is closed properly.
How to open the loading door of my Beko WUE 5411 XWW Washer?
If the loading door of your Beko Washer cannot be opened, it may be due to the door lock being activated because of the water level in the machine, so drain the water by running the Pump or Spin programme. The machine could be heating up the water or it is at the spinning cycle, so wait until the programme completes. The child lock may be engaged, so wait a couple of minutes for deactivation of the door lock. The loading door may be stuck because of the pressure it is subjected to, so grab the handle and push and pull the loading door to release and open it.
To Next Page
General
