Belmont PHOT-X II S 505 User Manual

MODEL 505
DENTAL X-RAY
Service Manual
○
R

Belmont PHOT-X II S 505 Specifications

General

Brand	Belmont
Model	PHOT-X II S 505
Category	Dental equipment
Language	English

Summary

Adjustment required when parts are replaced

Method to measure mA and kV

Error Code

3.1 Error Code: E.00

Details the meaning, release, and troubleshooting steps for error E.00.

3.2 Error Code: E.01

Explains error E.01, its causes, and solutions, including release procedures.

3.3 Error Code: E.02

Covers error E.02 related to low line voltage, including verification and solutions.

3.4 Error Code: E.03

Addresses error E.03 concerning high line voltage, with verification and solutions.

3.5 Error Code: E.05

Describes error E.05 related to low tube current during exposure and its remedies.

3.6 Error Code: E.06

Details error E.06 concerning high tube current and its troubleshooting steps.

3.7 Error Code: E.07

Explains error E.07 for tube current drop during exposure and its potential causes.

3.8 Error Code: E.08

Covers error E.08 related to excessive tube current during exposure and solutions.

3.9 Error Code: E.09

Addresses error E.09 concerning abnormal preheating power settings.

3.10 Error Code: E.10

Explains error E.10 when the exposure switch is already on at power-on.

3.11 Error Code: E.11

Details error E.11 indicating high tube current during preheating.

3.12 Error Code: E.12

Covers error E.12 related to tube current detection when power is on.

3.13 Error Code: E.14

Describes error E.14 for low tube voltage before exposure termination.

3.14 Error Code: E.15

Explains error E.15 for high tube voltage before exposure termination.

3.15 Error Code: E.16

Details error E.16 for dropped tube voltage during exposure.

3.16 Error Code: E.17

Covers error E.17 for high tube voltage during exposure.

3.17 Error Code: E.19

Addresses error E.19 related to overcurrent in the primary circuit of the high voltage transformer.

3.18 Error Code: E.20

Explains error E.20 when the exposure switch is pressed at high head temperature.

3.19 Error Code: E.22

Details error E.22 for abnormal communication between PC boards.

3.20 Error Code: E.23

Covers error E.23 when a button other than exposure switch is active at power-on.

3.21 Others

Covers general symptoms and checks not fitting specific error codes.

Setting Mode

4.1 Film type, digital mode and priority light

Explains how to set film type, digital mode, and priority light settings.

4.2 Tube current adjustment value

Describes the procedure for adjusting the tube current value.

4.3 Tube voltage adjustment value

Details the process for adjusting the tube voltage value.

4.4 Electronic chime ON/OFF

Covers enabling or disabling electronic chimes for button presses.

4.5 Manual setting of preheating power

Explains manual settings for preheating power for different kV/mA combinations.

4.6 Automatic adjustment of preheating power

Guides on automatic adjustment of preheating power for 70kV.

4.7 Setting the automatic lock

Describes how to set the automatic lock function for energy saving or locking.

4.8 Setting the standard density value for each tooth

Details setting standard density values for individual teeth, affecting exposure time.

4.9 Viewing the setting

Allows viewing various system settings without modification.

4.10 Error History

Describes how to access and view past error codes and their occurrences.

4.11 Number of Exposures

Explains how to view the total number of exposures made by the unit.

4.12 Estimated Air Kerma Display Setting

Covers setting the display mode for estimated Air Kerma radiation dose.

Exposure time

5.1 Assignable exposure time

Lists manually selectable exposure times for the unit.

5.2 Exposure time in the automatic setting mode

Explains calculation and lists exposure times based on various selections.

Parts replacement

6.1 Head

Details the procedure for replacing the x-ray head unit.

6.2 Power PC board

Provides instructions for replacing the power PC board.