Bestway Flowclear 58397

Questions and Answers

L
Linda DavisAug 4, 2025
Why is there no water flow in my Bestway Water Filtration System?
- E
  Edward RogersAug 4, 2025
  If your Bestway Water Filtration System isn't flowing water, several things could be the issue. First, check if the stopper plugs were removed and the debris screens inserted. Ensure air is released from the system. Verify that the control valve isn't set to 'Closed' but to the 'Filter' function. Also, inspect the strainer for blockages and clean it if needed. If none of these steps work, the sand filter may be broken, and you should call for service.
V
Victoria CollierAug 10, 2025
How to fix excessive filter pressure in Bestway Water Filtration Systems?
- R
  Ricky PhillipsAug 10, 2025
  Excessive filter pressure in your Bestway Water Filtration System can often be resolved with a few troubleshooting steps. Start by backwashing the filter to remove any accumulated dirt. If the sand bed is calcified, inspect the sand and change it if necessary. Also, ensure you are backwashing sufficiently until the water runs clear. If the pressure gauge is broken, consider replacing it.
R
rodriguezcarolAug 16, 2025
What to do if sand is flowing to the pool from my Bestway Water Filtration Systems?
- J
  Jason BautistaAug 16, 2025
  If sand is flowing into your pool from your Bestway Water Filtration System, here are a few things to check: - Make sure you're using the correct sand size. The recommended size is 0.45mm to 0.85mm #20 silica sand. - Always stop the sand filter when setting the control valve. - Check that the sand level is between the 'MAX' and 'MIN' markings on the collector hub. - Inspect the skimmer and replace it if broken.
M
Mr. David VanceAug 21, 2025
Why does the control valve leak from port D on my Bestway Water Filtration System?
- S
  Steve SanfordAug 21, 2025
  If the control valve on your Bestway Water Filtration System is leaking from port D, it might be set between two functions; ensure it is set to only one function. Another potential cause is a broken gasket, which would need to be replaced.
J
Jonathan WolfAug 28, 2025
How to stop connectors leaking in Bestway Water Filtration Systems?
- J
  James HaysAug 28, 2025
  If the connectors on your Bestway Water Filtration System are leaking, first check if the connector washers are correctly positioned; if not, reposition them. If the washer is broken, replace it. Also, inspect the O-ring on the hose connection and replace it if damaged. Finally, ensure all hoses are tightened properly.

Summary

SAFETY INSTRUCTIONS

SPECIFICATIONS

ASSEMBLY AND INSTALLATION

Assembly Steps

Step-by-step guide for assembling the sand filter components.

Load Pool-Grade Filter Sand

Instructions for adding the correct type and amount of filter sand.

Connect to the Pool

How to connect the sand filter to the swimming pool.

OPERATION

Control Valve Overview

Explanation of the sand filter's control valve and its functions.

Control Valve Functions

Details on using the Filter, Backwash, Rinse, Drain, Circulate, and Closed functions.

Air Release

Procedure for releasing air from the sand filter system.

First Time Use Instructions

Steps for initial setup, including backwashing and rinsing the sand.

Sand Filter Maintenance

Guidance on routine cleaning and upkeep of the sand filter.

CARE AND MAINTENANCE

Strainer Cleaning and Water Draining

Procedures for cleaning the strainer and draining pool water.

Winterizing the Unit

Steps to prepare the sand filter for winter storage.

TROUBLESHOOTING

LIMITED WARRANTY

Bestway Flowclear 58397 Specifications

General

Brand	Bestway
Model	Flowclear 58397
Type	Sand Filter Pump
Voltage	220-240V
Hose Diameter (inches)	1.25 inches
Filter Media	Sand
Pump's water flow rate	2000 GPH
System's water flow rate	2000 GPH
Sand Capacity	9 kg (20 lbs)
Pump power	0.37 kW
Suitable for pools of length	Above ground pools