Bestway Flowclear 58499

Questions and Answers

T
Tammy AllenAug 5, 2025
Why is there excessive filter pressure in my Bestway Water Filtration System?
- A
  Alan IrwinAug 5, 2025
  If your Bestway Water Filtration System experiences excessive filter pressure, it could be due to several reasons. The filter might be dirty, in which case you should backwash it. Another cause could be a calcified sand bed, so inspect the sand and change it if necessary. Also, ensure you are backwashing sufficiently until the water runs clear. Finally, the pressure gauge itself might be broken and need replacement.
W
wallsbrianAug 11, 2025
What to do if there is no water flow in Bestway Water Filtration Systems?
- S
  Sarah HaydenAug 11, 2025
  If you're experiencing no water flow in your Bestway Water Filtration System, start by checking if the stopper plugs were removed and the debris screens inserted. Ensure air has been released from the system. Verify that the control valve is set to the filter function, and clean the strainer if it's blocked. If none of these steps work, the sand filter may be broken, and you may need to call for service.
C
Catherine WheelerAug 17, 2025
How to stop sand flowing to the pool from Bestway Water Filtration Systems?
- M
  Marcia JacobsonAug 17, 2025
  If sand is flowing to the pool from your Bestway Water Filtration System, it might be because the sand is too small. It's recommended to use 0.45 mm to 0.85 mm #20 silica sand. Also, check if the level of the sand is too high; it should be between the marked “MAX” and “ MIN” on the collector hub. A broken skimmer could also be the cause, in which case you should replace it.
C
christopher01Aug 23, 2025
Why does the control valve leak from port D in Bestway Water Filtration Systems?
- J
  Jose BrooksAug 23, 2025
  If the control valve of your Bestway Water Filtration System leaks from port D, it could be because the control valve is set between two functions; ensure it is set to only one function. Alternatively, the gasket might be broken and needs replacement.
C
Christopher LaraAug 29, 2025
What to do if connectors leak in Bestway Flowclear 58499?
- R
  Rebecca HunterAug 29, 2025
  If the connectors of your Bestway Water Filtration System leak, it might be because the washer of the connectors is not in place; try repositioning it. If that doesn't work, the washer might be broken and needs replacement. Also, check for loose hoses and tighten them.

Summary

Safety Instructions

Specifications

Parts Reference and Assembly

Parts Reference Overview

Identifies all components of the sand filter system with reference numbers.

Assembly Instructions

Step-by-step guide on how to assemble the sand filter unit.

Sand Loading and Preparation

Load Pool-Grade Filter Sand

Instructions for correctly loading the recommended filter sand into the unit.

Connecting to the Pool

Pool Connection Methods

Details on how to connect the sand filter to pools, including specific valve types.

RCD Test and Operation

RCD Safety Test Procedure

Steps to perform the crucial Residual Current Device (RCD) test before use.

Sand Filter Operation

Guidance on operating the sand filter, including timer functions.

Control Valve Overview

Control Valve Functions

Detailed explanation of each control valve position and its purpose.

First Time Use Instructions

Initial Backwash and Rinse

Procedure for preparing the filter for first use by washing the sand bed.

Sand Filter Maintenance

Cleaning and Storage

Cleaning the Strainer

Instructions for cleaning the sand filter's internal strainer.

Draining Pool Water

Procedure for lowering or draining water from the pool using the filter.

Winterization and Long-Term Storage

Steps for preparing the filter for winter or extended storage.

Troubleshooting

Bestway Flowclear 58499 Specifications

General

Product Name	Bestway Flowclear 58499
Category	Water Filtration Systems
Product Type	Filter Pump
Voltage	110-120V
Frequency	60Hz
Filter Type	Cartridge Filter
Certification	CE