Bestway FLOWCLEAR 58663E User Manual

GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
58663E
OWNER’S MANUAL
bestwayusa.com/support
Visit the Bestway YouTube channel

Bestway FLOWCLEAR 58663E Specifications

General

Brand	Bestway
Model	FLOWCLEAR 58663E
Type	Sand Filter Pump
Filter Media	Sand
Voltage	220-240V
Filter cartridge included	No
Filter type	Sand
Flow Rate (L/h)	5678
Flow Rate (GPH)	1500
Pump's water flow rate (l/h)	5678
Pump's water flow rate (gal/h)	1500
Suitable for pool volume (gal)	2900

Summary

SAFETY INSTRUCTIONS

Important Safety Precautions

Essential safety measures to follow when using electrical equipment.

ELECTROCUTION AND SHOCK HAZARDS

Risk of Electrocution Warnings

Specific warnings about electrocution and related risks.

Electrical Safety Guidelines

Precautions for connecting to outlets and using GFCI protection.

GFCI WARNING

GFCI Test Procedure

Step-by-step guide to test the Ground Fault Circuit Interrupter.

POOL SUCTION FITTING INSTRUCTIONS

Suction Fitting Safety and Maintenance

Guidelines for proper installation, replacement, and maintenance of suction fittings.

SPECIFICATIONS

Filter Specifications

Technical details like diameter, area, pressure, temperature, and sand capacity.

PARTS REFERENCE OVERVIEW

Component Identification

Visual guide to all sand filter components with reference numbers.

ASSEMBLY

Component Preparation and Mounting

Steps for removing, checking, and mounting the sand filter.

Sand and Polysphere Loading

Instructions on loading the correct type and amount of sand or Polysphere.

CONNECT TO THE POOL

Connection Methods

Diagrams illustrating different ways to connect the filter to the pool.

GFCI TEST

Test Procedure

Step-by-step guide to test the Ground Fault Circuit Interrupter.

OPERATION

Control Valve Overview

Explanation of the control valve and its functions.

Filter Function

Primary function for filtering pool water.

Closed Function

Stops water flow between the filter and pool.

CONTROL VALVE FUNCTIONS

Backwash Function

Cleans the sand bed by reversing water flow.

Rinse Function

Used for initial startup and sand bed leveling after backwash.

Drain Function

Drains water from the pool or bypasses the filter.

Circulate Function

Circulates pool water, bypassing the sand filter for debris collection.

Air Release and First Use

Instructions for releasing air and initial setup procedures.

SAND FILTER MAINTENANCE

Cleaning the Strainer

Steps to remove and clean the strainer to maintain filter performance.

Lowering or Draining Pool Water

Procedure for removing pool water using the sand filter's drain function.

STORAGE

Winterization Procedures

Steps to winterize the sand filter to prevent damage from freezing temperatures.

TROUBLESHOOTING

Common Problems and Solutions

Lists issues like no operation, sand flow, no water flow, and their respective solutions.