To Next PageTo Next Page
What to do if Lay-Z-Massage System does not work in Bestway LAY-Z-SPA?
If the Lay-Z-Massage System on your Bestway Hot Tub isn't working, the air pump might be overheating. Unplug the pump and wait two hours for it to cool down. Then, plug it back in and press the Lay-Z-Massage System Button. Also, the Lay-Z-Spa Massage stops automatically, press the Lay-Z-Massage System Button to reactivate.
Why is the water in my Bestway LAY-Z-SPA not clean?
If the water in your Bestway Hot Tub isn't clean, it could be due to a few reasons. You might not be filtering the water for long enough, so try increasing the filtration time. Another common issue is a dirty filter cartridge, which you should clean or replace. Also, ensure you are following proper water maintenance procedures.
What to do if my Bestway LAY-Z-SPA Hot Tub has a leak?
If your Bestway Hot Tub has a spa pool leakage, it could be due to a tear or puncture in the spa. In this case, use the provided repair patch. Alternatively, the air valve might be loose. To check, apply soapy water to the air valve; if you see bubbles, it indicates a leak. To fix this, deflate the spa, hold the backside of the air valve from inside the spa wall, and turn the wrench clockwise to tighten it.
Why is my Bestway LAY-Z-SPA Hot Tub pump not heating properly?
If the Bestway Hot Tub pump does not heat properly, several factors could be at play. First, verify that the temperature isn't set too low. If it is, adjust it to a higher setting. Also, a dirty filter cartridge can cause heating issues, so clean or replace it. Another potential cause is the thermal cut-out, in that case, unplug the pump and allow it to cool down until the water temperature reaches 35°C (95°F) or lower before restarting. Finally, ensure the spa is covered to retain heat.
How to level Bestway Swimming Pool pump adapters with spa adapters?
One characteristic of PVC is that it changes shape, which is normal. Elevate the pump with wood or another type of insulated material to bring the pump's adapters level with the spa's adapters.
Why is my Bestway Swimming Pool leaking water from the pump adapters?
If your Bestway Swimming Pool is leaking water from the adapters between the pump and spa, insert the stopper caps onto the spa’s ports to prevent water from escaping and disconnect the pump. Check and make sure the seals are placed correctly inside the pump adapters. If the seals are missing or not installed correctly, please contact your local Bestway Aftersales Service Center for instructions. If the seals are correctly in place, reconnect the pump to the spa and hand-tighten the adapters.
How to troubleshoot the Lay-Z-Massage System on my Bestway Swimming Pool?
If the Lay-Z-Massage System on your Bestway Swimming Pool isn't working, the air pump may be overheating. Unplug the pump and wait two hours until it has cooled down, then plug it back in and press the Lay-Z-Massage System Button. If the Lay-Z-Spa Massage stops automatically, press the Lay-Z-Massage System Button to reactivate it. In case the air pump is broken, contact your local Bestway Aftersales Service Center for instructions.
What to do if the Bestway Swimming Pool control panel is not working?
If the control panel on your Bestway Swimming Pool is not working, it may be due to the auto-lock feature, which activates after 5 minutes of inactivity. If the lock icon is highlighted on the LED display, press the button for 3 seconds to unlock the control panel. If it still doesn't unlock, try restarting the pump by unplugging it and plugging it back in. If the control panel is not activated, press the on/off button for 2 seconds. If the problem persists, please contact your local Bestway Aftersales Service Center for instructions.
How to fix a Bestway Swimming Pool pump that does not heat properly?
If your Bestway Swimming Pool pump isn't heating properly, the temperature might be set too low; set it to a higher temperature. A dirty filter cartridge can also cause this, so clean or replace it. The thermal cut-out might have activated; unplug the pump and let it cool, then restart it when the water temperature reaches 35°C (95°F) or lower. Ensure the spa is covered. If these steps don't resolve the issue, the heating element may have failed, in which case you should contact your local Bestway After Sales service point to get instructions.
Why doesn't my Bestway Swimming Pool pump operate?
If your Bestway Swimming Pool pump isn't operating, the cause may be a power failure. Check the power source. If the power circuits are broken, contact your local Bestway Aftersales Service Center for instructions.
General| Control Panel | Digital control panel |
|---|---|
| Power Saving Timer | Yes |
| Shape | Round |
| Capacity | 4-6 people |
| Max Heat Capability | 40℃ (104℉) |
| Certifications | CE |
| Included Accessories | repair patch |
