EasyManua.ls Logo

Beurer IH 18 - User Manual

Beurer IH 18
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IH 18
EN Nebuliser
Instructions for use

Table of Contents

Questions and Answers

  • J
    Justin JohnsonAug 18, 2025
    How to fix Beurer IH 18 when the atomiser produces little or no aerosol?
    • W
      Wendy ClementsAug 18, 2025
      If your Beurer Medical Equipment atomiser produces little to no aerosol, first check that the amount of medicine in the atomiser is between the minimum of 0.5 ml and the maximum of 6 ml. Then, ensure the nozzles are not blocked; clean them if necessary. Also, make sure you are holding the atomiser in an upright position. Finally, consult your doctor to confirm that the medicine solution is suitable for nebulising, as some solutions may be too thick.
  • G
    Gregory DunnAug 20, 2025
    What to do if the output of Beurer IH 18 is too low?
    • A
      Alyssa MoralesAug 20, 2025
      If the output of your Beurer Medical Equipment is too low, check the hose for any kinks. Also, make sure that the filter is not blocked and verify that you are using the correct amount of inhalation solution.
  • M
    Mary CoxAug 23, 2025
    Is it necessary for each person to have their own Beurer Medical Equipment atomiser?
    • R
      Robert JonesAug 23, 2025
      It is absolutely necessary that each person uses their own atomiser for hygiene reasons when using Beurer Medical Equipment.
  • M
    Melissa Lopez DDSAug 26, 2025
    Why should I replace the Beurer IH 18 Medical Equipment atomiser regularly?
    • A
      Arthur JensenAug 26, 2025
      To guarantee a therapeutically effective particle spectrum and for hygiene reasons, regularly replace the atomiser on your Beurer Medical Equipment. The nozzle holes should not exceed a certain diameter, and the plastic is subject to wear due to thermal and mechanical stresses.
  • M
    Matthew ReevesAug 27, 2025
    What to do if some inhalation solution remains in the Beurer IH 18 atomiser?
    • J
      Joseph WeeksAug 27, 2025
      It is normal for some inhalation solution to remain in the atomiser of your Beurer Medical Equipment due to technical reasons. However, stop inhalation if you hear a notable difference in the noise of the atomiser.
  • R
    Robert FaulknerAug 30, 2025
    What to do if my Beurer IH 18 atomiser produces little or no aerosol?
    • T
      tyler67Aug 30, 2025
      If your Beurer Medical Equipment atomiser produces little or no aerosol, it could be due to several reasons. Ensure you have between 2 ml and 8 ml of medicine in the atomiser. Check the nozzles are not blocked; if they are, carefully clean them, rinsing if necessary, and only poke implements through the fine holes from the underside of the nozzle. Make sure the atomiser is held upright. Also, verify with your doctor that the medicine solution is suitable for nebulising, as solutions that are too thick may not work properly.
  • A
    arellanojohnSep 1, 2025
    Why do I need to replace the Beurer Medical Equipment atomiser at regular intervals?
    • J
      John MelendezSep 1, 2025
      There are two main reasons to regularly replace the atomiser in your Beurer Medical Equipment: Firstly, to maintain a therapeutically effective particle spectrum, as the nozzle holes should not exceed a certain diameter due to wear from thermal and mechanical stresses. This wear can alter the aerosol's droplet composition, affecting treatment effectiveness. Secondly, regular replacement is recommended for hygiene reasons.
  • D
    davidmoralesSep 3, 2025
    How to fix low output on Beurer IH 18?
    • G
      gracekimSep 4, 2025
      If the output of your Beurer Medical Equipment is too low, check for a kinked hose, a blocked filter, or too much inhalation solution.
  • J
    Jason TaylorSep 6, 2025
    Why does inhalation with the mask take longer with Beurer IH 18 Medical Equipment?
    • M
      Marcus MannSep 6, 2025
      Inhalation with the mask on your Beurer Medical Equipment may take longer because less medicine is inhaled per breath through the mask holes compared to using the mouthpiece. The aerosol mixes with ambient air through these holes.
  • A
    Anita VazquezSep 8, 2025
    Why should I replace the atomiser in my Beurer Medical Equipment regularly?
    • N
      Nicole ThomasSep 8, 2025
      You need to replace the atomiser of your Beurer Medical Equipment regularly to ensure the nozzle holes maintain the correct diameter for a therapeutically effective particle spectrum. The plastic is subject to wear due to thermal and mechanical stresses, especially in the nozzle attachment. This wear can alter the aerosol's droplet composition, affecting treatment effectiveness. Replacing the atomiser regularly is also recommended for hygiene reasons.

Summary

Getting to Know Your Instrument

Area of Application

Nebuliser for treating upper and lower respiratory tract with liquids/medication (aerosols).

Understanding Signs and Symbols

Instructional Symbols

Symbols indicating risks (Warning, Important) and general notes (Note).

Device and Packaging Symbols

Symbols found on the packaging and nameplate, denoting protection class, manufacturer, etc.

Safety Information and Warnings

General Safety Warnings

Crucial safety instructions for preventing injury and damage, including contact info and medical advice.

Usage and Health Precautions

Notes on using prescribed parts, checking contraindications, and stopping use if unwell.

Device and Accessory Overview

Nebuliser Unit Components

Diagram and labels identifying the main parts of the nebuliser unit.

Atomiser and Accessory Components

Diagram and labels identifying the atomiser and various accessories like masks and mouthpiece.

Initial Use and Operation

Setup and First-Time Preparation

Basic setup, cleaning atomiser/accessories, and attaching the compressed-air hose.

Mains Connection

Instructions for connecting the device to the mains power supply, including safety notes.

Operation Precautions

Hygiene, single-person use, rinsing atomiser, checking connections, and pre-use test.

Filling the Atomiser

Instructions for filling the atomiser with saline solution or prescribed medication, noting fill levels.

Treatment Procedure

Closing and Connecting Accessories

Steps for closing the atomiser and connecting mouthpiece, adult mask, or child mask.

Treatment Guidance and Limits

Inhalation posture, breathing, atomiser orientation, and operation limits (20 min on/40 min off).

Liquid Suitability Warning

Warning against essential oils/gargling solutions; consult doctor for sensitive conditions.

Filter Replacement

Filter Replacement Steps

Step-by-step guide on removing the filter cap, replacing the filter, and securing the cap.

Cleaning and Disinfection

Atomiser and Accessory Cleaning

Detailed instructions for cleaning atomiser and accessories to maintain hygiene and function.

Device Cleaning and Precautions

Cleaning the main unit with a soft cloth; avoid water ingress and abrasive products.

Hose Condensation Removal

Instructions for removing condensation from the air hose to prevent bacterial growth.

Disinfection Procedure

Procedure for disinfecting atomiser and accessories using boiling water and a vinegar solution.

Troubleshooting Common Issues

No or Low Aerosol Production

Troubleshooting steps for low or no aerosol, including medicine level and nozzle blockage.

Low Output or Residual Solution

Causes for low output (kinked hose, blocked filter) and explanation of residual solution.

Suitable Medicines and Mask Usage

Guidance on suitable medicines and specific instructions for mask use with babies/children.

Atomiser Replacement and Specifications

Atomiser Replacement Reasons

Reasons for regular atomiser replacement: particle spectrum and hygiene.

Technical Specifications Overview

Details on model, dimensions, weight, operating pressure, flow rates, and conditions.

Aerosol Properties and Particle Size

Technical details about aerosol output, delivery rate, and particle size (MMAD) with diagram.

Replacement Parts and Warranty

Available Replacement Parts

Information on available replacement parts and their material/reference numbers.

Warranty Conditions and Claims

Details on Beurer's warranty policy, coverage, duration, and the process for making a claim.

Beurer IH 18 Specifications

General IconGeneral
Easy to useYes
Power sourceAC
Product typeSteam inhaler
Product colorGrey, White
Weight and Dimensions IconWeight and Dimensions
Depth160 mm
Width155 mm
Height84 mm
Weight1300 g

Related product manuals