BIEMMEDUE EC 22 - User Manual

BIEMMEDUE EC 22

28 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

GENERATORE D'ARIA CALDA

GENERATEUR D'AIR CHAUD

WARMLUFTERZEUGER

SPACE HEATER

GENERADOR DE AIRE CALIENTE

ТЕПЛОВОЙ ГЕНЕРАТОР

EC/GE

EC 22 - EC 22 DV - EC 32 - EC 32 DV

GE 36 - GE 36 DV - GE 46 - GE 46 DV

L-L 101.02-BM

MANUALE D’USO E MANUTENZIONE

LIVRET D’ENTRETIEN

BEDIENUNGSANLEITUNG

INSTRUCTIONS MANUAL

MANUAL DE INSTRUCCIONES

РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ И ОБСЛУЖИВАНИЮ

Questions and Answers

C
Claudia MillerAug 11, 2025
What to do if the BIEMMEDUE EC 22 fan does not start or stops during start-up or heating?
- C
  Cynthia RodriguezAug 11, 2025
  If the fan doesn't start or stops, it could be due to several reasons: * **No electrical current:** Check the mains. * **Voltage below 175V:** The heater will restart automatically when the voltage exceeds 190 V. Check the supply voltage. * **Voltage above 265V:** The heater will restart automatically when the voltage is below 250 V. Check the supply voltage.
J
Jeffrey ChavezAug 31, 2025
What to do if the BIEMMEDUE Heater fan starts and flame lights, generating fumes?
- A
  ambermcdonaldAug 31, 2025
  If the fan starts, the flame lights, but it generates fumes, here are some possible causes and solutions: * **Insufficient combustion air:** Make sure the air inlet and outlet are free. * **Excess combustion air:** Check the position of the air regulation ring. * **Fuel contaminated or contains water:** Drain the fuel tank and load it with clean fuel. * **Air leaks in the fuel circuit:** Check the seals on the ducts and the diesel filter. * **Insufficient fuel at burner / Excess fuel at burner:** Check pump pressure.
T
Taylor StewartNov 19, 2025
Why does the BIEMMEDUE EC 22 Heater fan stop during start-up or heating?
- L
  Lisa SteeleNov 19, 2025
  The fan might stop during start-up or heating due to: 1. Presence of flame before the transformer ignites: Clean and eliminate diesel residue in the combustion chamber. 2. A defective photocell: Replace the photocell. 3. A defective electrical motor: Replace the electrical motor. 4. Defective electrical motor bearings: Replace the electrical motor bearings. 5. A burned-out condenser: Replace the condenser. 6. A defective electric ignitor: Check the connection of H.T. wires to electrodes and transformer. 7. A defective flame control box: Replace the control box. 8. Insufficient or no fuel at burner: Check the state of the motor-pump plastic coupling. 9. Defective solenoid or electric ignitor: Check the electrical connection. 10. Internal error of electronic device: Reset the devic...

BIEMMEDUE EC 22 Specifications

General

Air displacement	800 m³/h
Voltage	230 V
Frequency	50 Hz
Dimensions	950 x 450 x 530 mm
Weight	24 kg
Thermostat	Yes

Related product manuals

BIEMMEDUE EC 25

BIEMMEDUE EC 40

BIEMMEDUE EC 70

Preview: BIEMMEDUE EC 32

BIEMMEDUE EC 32

Preview: BIEMMEDUE EC Series

BIEMMEDUE EC Series

Preview: BIEMMEDUE EK 3 A

BIEMMEDUE EK 3 A

Preview: BIEMMEDUE EK Series

BIEMMEDUE EK Series

Preview: BIEMMEDUE EK C Series

BIEMMEDUE EK C Series

BIEMMEDUE BH 100

Preview: BIEMMEDUE CONFORT 35

BIEMMEDUE CONFORT 35

BIEMMEDUE FIRE Series

Preview: BIEMMEDUE Ballu BM2 GE 36

BIEMMEDUE Ballu BM2 GE 36