Binks M1-G HVLP - User Manual

Replaces
Part Sheet
77-2650R-6
Part
Sheet
77-2650R-7
Binks Model M1-G HVLP
GRAVITY FEED SPRAY GUN
The Binks M1-G HVLP Gravity Feed
Gun is a high quality sprayer that
produces fine finish for compliant and
non-compliant areas. A superbly bal-
anced forged aluminum body provides
you with extra comfort and control.
All components are machined and
finished to exacting tolerances and
only the best materials are used,
ensuring years of peak efficiency.
Simple to operate, the M1-G HVLP
provides exceptional finishes with
complex coatings such as primers,
base coats, clear coats, single stage
and waterborne compliant materials.
Additionally, specially designed air
and fluid nozzles enable the M1-G
HVLP to operate at more than 65%
transfer efficiency, in compliance with
air quality regulations as a high vol-
ume low pressure air spray gun.
The Binks M1-G HVLP Gravity
Feed Spray Gun includes a metal
paint cup with drip-proof cover.
To obtain optimum performance from
your new M1-G HVLP Gravity Feed
Spray Gun, read all instructions care-
fully.
PACKAGE CONTENTS
Please note your Binks M1-G HVLP
Gravity Feed Spray Gun package
was shipped with the following con-
tents. If anything in the following
list is missing, call 1-800-992-4657
for a prompt shipment to you of the
missing item.
Illustration Key
1. Air Nozzle Assembly
2. Gravity Feed Cup
3. Gun Body
4. Side Port Control
5. Fluid Control Knob
6. Air Connection 1/4" NPS(m)
2
1
3
4
5
6
PART
NO. DESCRIPTION QTY.
M1-G HVLP GRAVITY FEED SPRAY GUN ........ 1
77-2650 M1-G PART SHEET............................................ 1
54-4720 1 LITER GRAVITY FEED CUP ASSEMBLY.......... 1
SBBI-4-043 1 LITER CUP ASSEMBLY PART SHEET .............. 1
54-3871 GUNNERS MATE .............................................. 1
82-469 GUN BRUSH (ROUND)...................................... 1
192219 PLASTIC COATED GUN HOOK ........................ 1
82-221 CLEANING BRUSH (FLAT) ................................ 1
NOTE
IMPORTANT REGULATORY NOTE regarding
the use of this product appears on page 9.

Summary

Package Contents

Safety Information

Safety Terminology Definitions

Defines WARNING, CAUTION, and NOTE for safety emphasis.

Operational Hazards and Precautions

Covers warnings for manual reading, equipment misuse, guards, projectiles, pinch points, noise, static, fire, fumes, and respirator use.

Setup for Spraying

Connecting Gun to Air Hose

Instructions for connecting the air hose to the spray gun.

Connecting Gravity Feed Cup to Gun

Instructions for screwing the gravity feed cup into the spray gun.

Operating the M1-G HVLP Spray Gun

Controlling Material Flow

How to control fluid flow using the material valve control knob.

Controlling Fan Spray Pattern

How to adjust the fan spray pattern using the side port control.

Troubleshooting Common Issues

Faulty Spray Diagnosis

Explains causes and solutions for faulty spray, like improper cleaning.

Intermittent Spray Causes

Addresses fluttering spray caused by low material or clogged fluid passages.

Spray Gun Cleaning Instructions

Cleaning Gun and Gravity Feed Cup

Steps for cleaning the gun and gravity feed cup with solvent.

Maintenance Procedures

Replacing Air Valve and Spindle Assembly

Step-by-step guide for replacing the air valve and spindle assembly.

Replacing Cartridge Assembly

Instructions for removing and replacing the seal cartridge assembly.

Fluid Nozzles and Air Nozzle Selection

Standard Fluid Nozzles Chart

Details standard fluid nozzle part numbers, sizes, and compatible air nozzles.

Feathering Nozzles Chart

Lists feathering nozzles for gradual material valve opening and metering control.

Air Nozzle Pressure Recommendations

LVLP Air Nozzle Recommendations

Provides pressure recommendations for LVLP air nozzles like 93P and 92P.

HVLP Air Nozzle Recommendations

Provides pressure recommendations for HVLP air nozzles like 96G, 95P, 97P, 905P, 907P, and 94P.

Assembly Drawing

Parts List

General Spray Instructions

Spray Technique Guidelines

Details proper gun handling, stroke, and distance for a good finish.

Oil and Water Extractor Importance

Explains the dual purpose of a Regulator/Extractor for clean air and pressure control.

Hose Recommendation for Air Supply

Compares 1/4" and 5/16" hose performance and recommends 5/16" for reduced pressure drop.

Important Regulatory Note

HVLP Spray Gun Operation Limits

Advises on regulatory limits for HVLP spray gun atomizing pressure.

Air Nozzle Test Gauge Assembly

Lists test gauges for various air nozzles and their purpose.

Accessories

Warranty Information

Binks Worldwide Sales and Service

Provides contact information for technical assistance and distributor locations.

Binks M1-G HVLP Specifications

General

Brand	Binks
Model	M1-G HVLP
Category	Paint Sprayer
Language	English