Biolight Q3 User Manual

I
Product Information
 Product Model: Q3/Q5/Q7
 Product Name: Patient monitor
 Manufacturer Name: Guangdong Biolight Meditech Co.,Ltd.
 After Service Contact Information:
Address: No.2 Innovation First Road, Technical Innovation Coast,
Hi-tech Zone, Zhuhai, P.R. China
Fax: +86-756-3399919
Post code: 519085
Toll-free consultation hot line: +86-400-8818-233
Revision History
This manual has a revision number. This revision number changes
whenever the manual is updated due to software or technical specification
change. Contents of this manual are subject to change without prior notice.
 Document No.: J/Q-I-008
 Revision number: V1.1
 Release time: Jun.2017
Copyright © 2017 Guangdong Biolight Meditech Co., Ltd. All rights
reserved.
Statement
Manufacturer holds the copyright of this manual, and we are also entitled
to deal with this manual as confidential files. This manual is only used for
operation, maintenance and service of product, someone else can not publish
the manual.
This manual contains exclusive information protected by copyright laws
and we reserve its copyright. Without written approval of manufacturer no
parts of this manual shall be photocopied, Xeroxed or translated into other
languages.
The contents contained in this manual are subject to amendments without
notification.

Biolight Q3 Specifications

General

Brand	Biolight
Model	Q3
Category	Medical Equipment
Language	English

Summary

Product Information

Manufacturer Contact and Revision History

Details manufacturer contact information and document revision history.

Chapter 1 General Introduction

1.1 Intended Use

Describes the intended applications and limitations of the patient monitor.

1.2 Main Unit Overview

Provides a visual overview of the monitor's front, side, bottom, and rear views.

Chapter 2 Safety

2.1 General Safety Information

Covers essential warnings and precautions for safe monitor operation.

2.4 Safe Operation Conditions

Details conditions for safe and effective monitor use, including environmental factors.

Chapter 3 Basic Operations

3.1 Initial Setup and Checks

Guides users through unpacking, checking, and preparing the monitor for use.

3.3 Screen Interface and Navigation

Explains the monitor's screen layout, areas, and how to use smartkeys.

3.10 Parameter and Module Configuration

Covers setting measurement modules, using labels, and resolving label conflicts.

Chapter 5 Alarm

5.1 Alarm Classification and Levels

Defines alarm categories (physiological, technical, prompt) and severity levels.

5.3 Alarm Management

Details how to set alarm volume, parameters, silence, pause, and acknowledge alarms.

Chapter 7 ECG

7.2 ECG Monitoring Procedure

Outlines safety, skin prep, electrode placement, cable connection, and lead selection.

7.5 ECG Settings

Covers ECG parameter setup, modes, QRS volume, primary lead, and waveform settings.

Chapter 9 SpO2

9.3 SpO2 Monitoring Procedure

Guides on selecting, connecting, applying SpO2 sensors, and interpreting display.

9.5 SpO2 Parameter and Settings

Details SpO2 parameter settings including NIBP same limb, average time, PR source, and Masimo settings.

Chapter 11 NIBP

11.2 NIBP Monitoring Procedure

Covers NIBP prep, modes, measurements, display, and limitations.

11.7 NIBP Settings

Explains NIBP unit, alarm source, initial inflation pressure, venipuncture, and resetting.

Chapter 16 Reviewing

16.1 Graphic Trends Review

Describes how to review graphic trends, select parameters, intervals, and record data.

16.3 Specific Data Review

Covers reviewing NIBP results, parameter alarms, and holographic waveforms.

Chapter 17 Calculations

17.1 Drug Dose Calculation

Details the steps for calculating drug dosage, units, and using the titration table.

17.2 Hemodynamic Calculation

Explains steps for hemodynamic calculations and lists input/output parameters.

Chapter 21 Maintenance and Cleaning

21.1 Equipment Maintenance

Outlines periodic safety checks and maintenance procedures for optimal performance.

21.2 Cleaning Procedures

Provides guidelines for cleaning the monitor and its accessories safely and effectively.

Appendix A Product Specifications

A.1 Safety, Environmental, and Physical Specs

Lists safety, environmental, and physical specifications for the monitor and modules.

A.3 Measurement Specs - ECG, Resp, NIBP

Provides detailed technical specifications for ECG, Respiration, and NIBP measurements.

A.4 Measurement Specs - SpO2, Temp, IBP, CO2, AG

Lists detailed technical specifications for SpO2, Temperature, IBP, CO2, and AG measurements.

Appendix C Alarm Messages

C.1 Monitor Alarm Messages

Lists all system, ECG, Resp, SpO2, Temp, NIBP, IBP, CO2, and AG alarm messages.