To Next PageTo Next PageHow to fix Bissell ProHeat 2X Revolution Pet with reduced or no spray?
If your Bissell Vacuum Cleaner has reduced or no spray, it could be due to an empty clean water tank. Refill the tank. Alternatively, the clean water tank may not be seated properly. Turn the power OFF, remove, and then reseat the tank to ensure it is correctly in place.
Why Bissell Vacuum Cleaner has loss of suction power?
A loss of suction power in your Bissell Vacuum Cleaner can occur due to several reasons. The dirty water tank may not be seated properly; make sure to pick up the tank and reseat it on the machine. The dirty water tank might be full, in which case you should empty it. Check the rubber tab on the dirty water tank to ensure it's sealed tightly by pressing firmly on all edges. Also, ensure the accessory hose door is closed tightly and locked into place. The nozzle could be clogged with pet hair or debris; use the nozzle clean out tool. Lastly, the brush roll cover might not be snapped into place; remove and replace the nozzle and brush roll cover.
What to do if Bissell Vacuum Cleaner has no spray through hose & tool?
If your Bissell Vacuum Cleaner has no spray through the hose and tool, it might be because the hose to the machine is not primed or has lost prime. With the machine OFF and unplugged, remove the nozzle from the foot. Place a ballpoint pen in the black cylinder next to the screw. When water bubbles up, remove the pen and reassemble the nozzle and hose. You can also hold the end of the hose below the water level in the tank to prime it. Additionally, ensure the clean water tank is full and properly seated. If issues persist, with the machine OFF and RECLINED, press the CleanShot button ON and wait for the CleanShot to drain for a few seconds to re-prime the machine. Refill the tank if it's empty and make sure the tank is seated properly by turning the power OFF and reseating the tank.
What to do if Bissell Vacuum Cleaner has no power?
If your Bissell Vacuum Cleaner has no power, first ensure that the cleaning mode switch isn't mistaken for the power switch. Flip the power switch on the left side of the machine to turn it ON. Also, check if the outlet is active by plugging in a different device. If the tank is overfilled, water may be caught in the space between the tank and tank handle. With the cap secured, hold the tank at an angle over a sink or drain so any extra water can pour out of the space, and then wipe the tank dry with a cloth.
What to do if Bissell ProHeat 2X Revolution Pet has no spray through CleanShot?
If there is no spray through the CleanShot on your Bissell Vacuum Cleaner, start by refilling the clean water tank if it's empty and ensure that the clean water tank is properly seated by turning the power OFF, removing, and reseating the tank. Make sure the machine is reclined by pressing the recline pedal and bringing the handle down. If the pump has lost prime, with the machine OFF and unplugged, remove the nozzle from the foot and place a ballpoint pen in the black cylinder next to the screw until water bubbles up, then remove the pen and reassemble the nozzle.
What to do if CleanShot sprays when Bissell ProHeat 2X Revolution Pet Vacuum Cleaner is OFF?
If the CleanShot sprays when your Bissell Vacuum Cleaner is OFF, it indicates that the CleanShot button is not in the OFF position. Press the CleanShot button to turn it off. The button window will show the color red and a “O” symbol when it is in the OFF position.
General| Type | Upright Carpet Cleaner |
|---|---|
| Power Rating | 6.8 amps |
| Cleaning Path Width | 11 inches |
| Tank Capacity | 1 gallon |
| Heatwave Technology | Yes |
| Cord Length | 22 feet |
| Brush Type | Dual DirtLifter PowerBrushes |
| Heater | Yes |
| Specialized Pet Tools | Yes |
| Warranty | 3-year limited |
Covers fire, electric shock, and injury prevention guidelines for safe operation.
Steps for assembling the carpet cleaner, including required tools.
Step-by-step guide for filling the clean water tank with formula and water.
Details on MAX/DEEP Clean and Express Clean modes for carpet cleaning.
Instructions for using the CleanShot feature on tough stains.
How to use Deep Stain, 7cm, 10cm, 15cm, and Spraying Crevice tools.
Guide for using the 2-in-1 Upholstery and Stain Trapper tools.
Instructions for rinsing the machine and cleaning brushes/nozzles.
Steps for removing and cleaning the dirt bin.
Details the two-year limited warranty, exclusions, and important notes.
Provides contact details for warranty claims and service in Australia and New Zealand.
