◈ Information
This installation guide contains quick information required for the product installation. Refer
to the User’s Manual in the CD that comes with the product for detailed installation
instructions. The CD contains the following information.
1. Manual: User’s Manual, Code table, and Control commands
2. Driver: Windows driver and OPOS driver
3. Utility: Logo download tool and virtual memory switch adjustment tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Checking the Contents
SRP-F310 / SRP-F312
Power Cord
Paper Roll
Procuct Installation CDProcuct Installation CD
CD
Installation Guide
Connecting Cables◈
1. Turn off the printer and ECR (host computer).
2. Connect the power cord to the adapter and connect the adapter to the power supply
connector of the printer.
3. Check the type of the interfaces at the back of the printer (serial, parallel, USB, and
Ethernet), and connect the interface cable.
4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer.
◈ Installing Paper Rolls
1. Press the [Open Cover] button and open
the cover.
2. Insert new paper roll in the correct
direction.
3. Pull the paper slightly, and close the
cover.
※ Note
When closing the cover, hold down the
center of the cover so that the paper is
closely attached to the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
※ Note: Remaining paper sensor position adjustment
SRP-F310/312 printers have sensors to
notify when the paper is about to run out.
When the paper is about to run out, paper
lamp (red) in the operation panel will be on.
If the light is on while there is sufficient
paper, move up the adjustment lever
slightly.
※ Do not use paper wider than 80 mm or plastic paper tube when using a printer
that specifies 80 mm paper.
◈ Using 83mm Paper
Remove the partition installed in the printer to use 83mm roll paper.
※ Refer to the User’s Manual for detailed instructions on how to remove the partition
safely.
◈ Using Operation Panel
• POWER indicator
Blue light will be on when power is supplied to the printer.
• ERROR indicator
Red light will be on for error conditions such as no paper or open cover.
• PAPER indicator
Red light will be on when the paper is about to run out or if there is no paper. If this light
keeps blinking, it means either self test state or macro execution standby state.
• FEED button
Press feed button to feed the paper. Pressing and holding the feed button will feed the paper
continuously.
◈ DIP switch setting
DIP switch setting must be done while the printer is turned off. Changes during power on are
not recognized.
1. Serial interface setting
• DIP switch 1
Switch Function ON OFF Default
1-1 Auto-Cutter Selection Disable Enable OFF
1-2 Handshaking XON/XOFF DTR/DSR OFF
1-3 Word length 7 bit 8 bit OFF
1-4 Parity check YES NO OFF
1-5 Parity selection EVEN ODD OFF
1-6
Baud rate (bps) Refer to Table 1 shown below
OFF
1-7 ON
1-8 OFF
2. Parallel / USB interface setting
• DIP switch 1
Switch Function ON OFF Default
1-1 Auto-Cutter Selection Disable Enable OFF
1-2 N/A - - OFF
1-3 N/A - - OFF
1-4 N/A - - OFF
1-5 N/A - - OFF
1-6 N/A - - OFF
1-7 N/A - - OFF
1-8 N/A - - OFF
• Table 1 – Baud rate (bps) selection
Baud rate 1-6 1-7 1-8 Default
2400 ON OFF OFF
9600
4800 ON OFF ON
9600 OFF ON OFF
19200 OFF OFF OFF
38400 OFF ON ON
57600 OFF OFF ON
115200 ON ON ON
◈ Self Diagnostics
1. Check whether the paper is inserted correctly.
2. Turn on the printer while depressing the Feed button. Self diagnostics will begin.
3. The printer prints the current status of the printer such as the version of the ROM and DIP
switch setting.
4. The printer prints the current status and stops after printing the following statement.
(PAPER indicator keeps blinking.)
SELF-TEST PRINTING.
PLEASE PRESS THE FEED BUTTON
5. Press the Feed button to continue to print. Then the printer will print the character sets that
can be printed.
6. Self diagnostics will end automatically and the paper will be cut after printing the
following statement.
*** COMPLETED ***
7. The printer will be in normal mode after self diagnostics is completed.
※ Note
You can check whether the printer operates normally or not through self diagnostics. You
can check printing quality, ROM version, and DIP switch settings through self diagnostics.
Printer Installation Guide
KN04-00035A (Rev.1.4)
Front Printing Thermal Printer SRP-F310/312
Control Lever
Drawer Kick-Out Cable
Power Connector
Interface Connecto
To Next Page
Need help?
General
Weight and Dimensions
