ENGLISH
7
Minimum Gauge for Cord Sets
Volts Total length of cord in meters (m)
120 V - 127V 0 - 7 7 - 15 15 - 30 30 - 50
220 V 0 - 15 15 - 30 30 - 60 60 - 100
Ampere Rating
Minimal cross-sectional area of the
cord in milimeters (mm
2
)
More
Than
Not
More
Than
0 6 1,0 1,5 1,5 2,5
6 10 1,0 1,5 2,5 4,0
10 12 1,5 1,5 2,5 4,0
12 16 2,5 4,0 Not Recommended
• Do not place any object on top of the charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source.
The charger is ventilated through slots in the top and the
bottom of thehousing.
• Do not operate the charger with a damaged cord
orplug.
• Do not operate the charger if it has received a sharp
blow, been dropped or otherwise damaged in any way.
Take it to an authorized servicecenter.
• Do not disassemble the charger; take it to an
authorized service center when service or repair is
required. Incorrect reassembly may result in a risk of electric
shock, electrocution orfire.
• Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock. Removing the battery will not reduce
thisrisk.
• NEVER attempt to connect 2 chargerstogether.
• The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage. This does not apply to the
vehicularcharger.
WARNING: Shock hazard. Do not allow any liquid to get
inside the charger. Electric shock mayresult.
WARNING: Burn hazard. Do not submerge the battery in
any liquid or allow any liquid to enter the battery. Never
attempt to open the battery for any reason. If the plastic
housing of the battery breaks or cracks, return to a service
center for recycling.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only BLACK+DECKERrechargeable batterys. Other
types of batteries may overheat and burst resulting in
personal injury and propertydamage.
NOTICE: Under certain conditions, with the charger plugged
into the power supply, the charger can be shorted by foreign
material. Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool, aluminum
foil or any buildup of metallic particles should be kept away from
the charger cavities. Always unplug the charger from the power
supply when there is no battery in the cavity. Unplug the charger
before attempting toclean.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if the
battery is charged when the air temperature is between
65°F and 75°F (18° – 24°C). DO NOT charge the battery
in an air temperature below +40°F (+4.5°C), or above
+104°F (+40°C). This is important and will prevent serious
damage to the battery.
2. The charger and battery may become warm to the touch
while charging. This is a normal condition, and does
not indicate a problem. To facilitate the cooling of the
battery after use, avoid placing the charger or battery
in a warm environment such as in a metal shed or an
uninsulated trailer.
3. If the battery does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. Move the charger and battery to a location where
the surrounding air temperature is approximately
65°F – 75°F (18° – 24°C);
d. If charging problems persist, take the tool, battery and
charger to your local service center.
4. The battery should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery in
the cavity. Unplug the charger before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
To Next Page
Loading...
Need help?
General
