This document describes the BLACK+DECKER BEMWH551 Hover mower, a mains-powered appliance designed specifically for mowing grass in a domestic setting. The mower is intended for consumer use and emphasizes safety, proper operation, and maintenance to ensure effective and long-lasting performance.
Function Description
The BLACK+DECKER BEMWH551 is a hover mower, meaning it operates on a cushion of air, making it lightweight and highly maneuverable across the lawn. Its primary function is to cut grass efficiently. The mower is equipped with a motor on/off grip and a power button for easy control. It features a blade system that can be adjusted for different cutting heights (28mm to 38mm), allowing users to customize the lawn finish. The hover design allows it to glide over various terrains, making it suitable for lawns with minor irregularities.
Usage Features
The mower is designed for ease of use, with a focus on safety during operation.
- Assembly: The handle assembly is straightforward, involving attaching the lower handle to the main body and then the upper handle to the lower handle using latches and screws. The upper handle latch can be positioned either on the outside or inside, based on user preference. Before starting, users are instructed to ensure the mower is in good working order, the power button is off, and the cable plug is disconnected.
- Starting and Stopping: To start the mower, the user squeezes the motor on/off grip towards the upper handle and presses the power button. The power button remains depressed as long as pressure is maintained on the grip. Once the motor picks up speed, the mower lifts on an air cushion, becoming very light and maneuverable. To stop the motor, the user simply releases pressure on the motor on/off grip, causing the power button to click off and the mower to sink to the ground. For emergency stops, releasing the motor on/off grip immediately stops the motor.
- Mowing Technique: The manual recommends a specific mowing pattern to optimize results and minimize the risk of cutting the mains cable. Users should place the bulk of the mains cable on the lawn near the starting point and proceed in a systematic pattern, turning right and left as needed. It's crucial to avoid working towards the cable. Cable retention clips are provided to secure the cord neatly to the handle assembly.
- Safety during Operation: Several safety precautions are highlighted. Users must wear substantial footwear and long trousers, avoiding barefoot operation or open sandals. Loose-fitting clothing should also be avoided. The area to be mowed must be thoroughly inspected for objects that could be thrown by the machine. Hands and feet must be kept away from the rotating blade and discharge openings. The mower should only be used in daylight or good artificial light and not in damp or wet conditions. When working on slopes, users should work across the face of slopes, never up and down, and exercise extreme caution when changing direction. The mower should not be pulled backward unless absolutely necessary, and users should always look down and behind when moving backward. The machine should not be operated without all safety protective devices in place and working.
- Cable Management: Users are advised to keep the mains cable away from the blade and be aware of its position at all times. If the cord becomes damaged during use, it must be disconnected immediately, and the cord should not be touched before disconnection.
- Blade Adjustment: The mower's cutting height can be changed from 28mm to 38mm by using the blade bolt spanner to remove the blade bolt, flipping the blade holder disc, and repositioning the blades on their anchor pins.
Maintenance Features
Regular maintenance is crucial for the mower's safe and efficient operation.
- Pre-use Checks: Before each use, the appliance should be visually inspected for damaged or defective parts, including the blade, blade bolt, blade assembly, guards, switches, and cables. Worn or damaged components should be replaced in sets to maintain balance.
- Cleaning: After use, the mower should be turned off, and the blade allowed to stop completely. It should be cleaned with mild soap and a damp cloth. Clippings accumulated on the underside of the deck should be removed. If the mower has been used in areas with fertilizers or chemicals, it should be cleaned immediately to prevent corrosion.
- Blade Maintenance: The blades should be periodically checked for damage and balance. If broken or unbalanced, both blades must be replaced. Only manufacturer-recommended blades should be used. When servicing blades, the power button must be in the off position, and the power plug disconnected.
- General Maintenance: All nuts, bolts, and screws should be kept tight to ensure safe working conditions. The grass collector should be checked for wear or damage and replaced if necessary. The appliance should never be used without the grass collector. The motor housing should be regularly cleaned with a damp cloth, avoiding abrasive or solvent-based cleaners. A blunt scraper can be used to remove grass and dirt from underneath the guard.
- Cable Inspection: The mains cable and any extension cables should be frequently inspected for damage, wear, or aging. Damaged cables must be replaced by an authorized repair agent to prevent hazards.
- Storage: When not in use, the appliance should be stored in a dry place, out of reach of children. The machine should always be allowed to cool down before storage.
Need help?
General
To Next Page
