To Next PageTo Next PageWhy is my Blomberg WM 77110 NBL00 load still too wet?
If your Blomberg washer load is still too wet at the end of the program, add more laundry to the drum and start a “Spin” or “Spin&Drain” cycle if the unbalance detection is due to 1-2 small items in the drum. Use proper amount of HE detergent, if there are poor spinning results due to not using HE detergent or using excessive amount of detergent.
How to reduce vibration in my Blomberg WM 77110 NBL00?
If your Blomberg washer vibrates, shakes, or makes too much noise, adjust the washer feet. Ensure that the shipping bolts have been removed. If there is a small amount of laundry in the drum, add more laundry for even load distribution. If the drum is overloaded or the clothes are distributed unevenly, reduce the amount of laundry or balance the load by hand. Also, make sure that nothing is touching the washer.
Why is my Blomberg Washer not turning on?
If your Blomberg washer is completely dead and nothing is displayed on the screen, check the plug. Check the fuse / circuit breaker. Check the supply power. Press the “On/Off” button.
Why didn't my Blomberg Washer spin?
If your Blomberg washer did not spin, the automatic spin correction system might have been activated due to the unbalanced distribution of the laundry in the drum. Laundry should be rearranged and re-spun, if the laundry in the drum may be tangled up too much. Add more laundry to the drum and start a “Spin” or “Spin&Drain” cycle if the unbalance detection is due to 1-2 small items in the drum. Check the drain hose and straighten if necessary. See “Spin Speed Selection.”, if “No spin” setting may be adjusted. Clean the drain pump filter, if drain pump filter or drain itself may be clogged. If the house drain pipes are clogged, call a plumber for assistance.
What to do if the door of my Blomberg Washer will not open?
If your Blomberg washer door won't open, run a “Drain”, “Spin” or “Drain&Spin” program if the water level is too high. If the washer is heating up water or is at the spinning cycle, wait until the process is over. The door can be opened a few minutes after the program has stopped. If the door still can not be opened after minimum ten minutes the program has stopped, turn the on/off button to the off position. In this situation, call the qualified service technician.
Provides a visual overview of the washer's components.
Lists technical details like dimensions, weight, and power requirements.
Guides on choosing placement, clearances, and ventilation for installation.
Details on removing packaging, shipping bolts, and leveling the washer.
Instructions for electrical hookup, grounding, and water supply connections.
Guidance on drain hose setup and final installation checks.
Steps for moving the washer and guidelines for its disposal.
Steps for initial operation, sorting, and preparing laundry.
How to load the washer and use detergents and additives correctly.
Explanation of how the washer adjusts water usage for efficiency.
Overview of control panel buttons, display, and symbols.
Details on selecting programs, wash cycles, and special programs.
How to adjust wash temperature and spin speed for cycles.
Explanation of selectable options like Super Wash, Soak, and Extra Rinse.
Using time delay, changing settings, and canceling programs.
Steps for starting, pausing, adding laundry, and ending cycles.
How to activate/deactivate child lock to prevent tampering.
Steps to start, cancel, and add laundry to a wash cycle.
Procedures for discharging water without spinning or re-spinning.
Actions to take after the wash cycle has finished.
How to clean the detergent dispenser, door seal, and drum.
Instructions for cleaning water inlet strainers and the drain pump filter.
How to remove scale buildup using a descaling agent.
Solutions for issues with water not filling or draining properly.
Troubleshooting door issues, time delays, and unexpected stops.
Addressing extended cycle times, foam, and poor wash results.
Troubleshooting when the washer does not spin or loads are unbalanced.
Solutions for stains, discoloration, stiffness, and odors.
Diagnosing and resolving noises from the drum, drain pump, and vibration.
Troubleshooting blank screens and water cut-off symbols.
General