BLUBERY GSW02A - User Manual

Questions and Answers

B
Bryan HenryAug 14, 2025
Why does my BLUBERY Pressure Washer have low pressure?
- J
  John MillerAug 14, 2025
  If your BLUBERY Pressure Washer has low or no pressure, first, attach the required nozzle tip. Then, ensure the water supply faucet is fully open and there are no kinks or blockages in the hose. Verify that the water supply pressure is a minimum of 30 psi, 4 GPM. Clean the inlet water filter if it's clogged. Squeeze the trigger to release any air in the pump while the machine is running. Finally, set the RPM (throttle lever) to the FAST position.
A
albert25Aug 17, 2025
Why does my BLUBERY GSW02A Pressure Washer engine stop after starting?
- A
  Amanda CannonAug 17, 2025
  If your BLUBERY Pressure Washer engine stops soon after starting, check the oil and fuel levels to ensure they are sufficient. Also, make sure the choke lever is not in the Close position; move it to the Open position immediately after starting the engine.
L
lopezcrystalAug 20, 2025
Why is my BLUBERY Pressure Washer not siphoning detergent?
- C
  Crystal GordonAug 21, 2025
  If your BLUBERY Pressure Washer is not taking in detergent, make sure the detergent siphon tube is properly connected. Replace the tube if it's damaged. Use the black nozzle when applying detergent. Check the detergent adjustment knob position. Clean the nozzle if it’s clogged. Detach the detergent siphon tube and clean the fitting with a tip cleaner if the pump detergent siphon fitting is clogged. Only use detergent approved for use with a pressure washer.
L
lbrownAug 25, 2025
What to do if my BLUBERY Pressure Washer engine lacks power?
- Q
  qfosterAug 25, 2025
  If your BLUBERY Pressure Washer engine lacks power, the air filter or carburetor may be clogged. Clean or replace the air filter. Clean the carburetor.
Z
Zachary WilsonAug 27, 2025
Why does my BLUBERY GSW02A Pressure Washer sound abnormal?
- M
  Manuel EstradaAug 27, 2025
  If your BLUBERY Pressure Washer engine sounds abnormal or overloaded, adjust the throttle lever to the Fast position, and clean the nozzle with a tip cleaner.
D
Danny LopezAug 30, 2025
Why is my BLUBERY Pressure Washer leaking water from the joints?
- D
  david68Aug 30, 2025
  If there is water leakage at joints/connections on the gun, hose, or pump of your BLUBERY Pressure Washer, the seal ring may be damaged. Replace it with a back-up O-ring or purchase an accessory kit.
D
Danielle LewisSep 3, 2025
Why does my BLUBERY GSW02A Pressure Washer stop when tilted?
- W
  William HillSep 3, 2025
  If your BLUBERY Pressure Washer engine stops while moving or being tilted, do not tilt the machine past 15° when operating. Check the oil level and ensure it is above the minimum level on the dip stick.
J
jessicacooperSep 6, 2025
What to do if the hose won't connect to my BLUBERY GSW02A?
- S
  Sarah AndersonSep 6, 2025
  If the high-pressure hose can’t be connected to the pump or gun of your BLUBERY Pressure Washer, put lubricating oil or water on the O rings.
K
Karen RobinsonSep 10, 2025
Why can't I squeeze the trigger on my BLUBERY Pressure Washer?
- A
  anthony91Sep 10, 2025
  If the trigger on your BLUBERY Pressure Washer can’t be squeezed, open the safety lock.