Why is my BOC MIG 250C Welding System welding torch overheating?
If the welding torch overheats with your BOC Welding System, it might be underrated for the welding application. Check that the welding torch is suitable for the application.
How to stop wire spool drag or overrun on my BOC MIG 250C?
If the wire spool drags or overruns on your BOC Welding System, the spindle brake might be set too tight or too loose, or the spool might not be properly located on the spindle. Adjust the spindle brake and make sure the spool is properly located.
How to fix no or low welding output in my BOC Welding System?
If your BOC Welding System has no or low welding output, the cause might be a bad or incorrect primary connection, or a lost phase. To resolve this, check the primary cable connections to make sure they are in good condition.
Why is the wire live before welding with my BOC MIG 250C?
If the wire is live when feeding through the cable and torch before welding with your BOC Welding System, it could be a faulty wire inch switch or inappropriate use of the torch trigger switch. Inspect the wire inch switch and use the torch trigger switch appropriately.
How to fix wire restriction and gas leaks in my BOC MIG 250C Welding System?
If your BOC Welding System has wire restriction, gas leaks, or no trigger control, the universal adaptor might not be correctly mounted or secured, the internal guide could be the incorrect size, or the contact pins might be bent. Check and secure the universal adaptor, ensuring the correct size and straight contact pins.
Why is my BOC MIG 250C Welding System wire shaving or snarling?
If your BOC Welding System is experiencing wire shaving or snarling, it might be due to incorrect wire guide sizes or misalignment. Ensure correct wire guide sizes and alignment.
What causes erratic feeding and unstable arc in my BOC Welding System?
If your BOC Welding System is showing erratic feeding, wire shudder, wire burnback, unstable arc, or spatter, it may be due to an incorrect size of contact tip, incorrect contact tip to nozzle distance for metal transfer mode, or inferior contact tip material. Replace the contact tip with the correct size and ensure proper distance.
Why can't I control wire feed speed or amperage on my BOC Welding System?
If there's no control over wire feed speed or amperage control in your BOC Welding System, it could be a faulty wire speed feed potentiometer, or the wire feed motor is in an overload or trip condition. Test and replace the wire speed feed potentiometer as needed.
How to resolve wire slippage and deformation in my BOC Welding System?
If your BOC Welding System is experiencing wire slippage or wire deformation, the cause may be incorrect feed roll size, incorrect tension adjustment, or misalignment. Adjust the wire feed rolls to the correct size and tension.
Why is the wire feed erratic and snarling in my BOC MIG 250C Welding System?
If your BOC Welding System experiences erratic wire feed or wire snarls up at the outlet guide, the liner might be the incorrect type and size for the wire in use, or it might be worn, dirty, too long or too short. Replace the liner with the correct type and size.
Details health risks associated with welding processes including UV rays, fumes, and gases.
Recommends appropriate personal protective equipment (PPE) for welding operations.
Provides critical safety measures to avoid electric shock during welding.
Outlines the user's obligations for safe operation and maintenance of the equipment.
Provides indicative welding parameters for different materials and processes.
Step-by-step guide for installing the MIG/MAG welding process.
Step-by-step guide for installing the MMA welding process.
Procedure for setting up the machine for MIG welding operations.
Procedure for setting up the machine for MMA welding operations.
General| Output Current Range | 30-250A |
|---|---|
| Welding Current Range | 30-250A |
| Weight | 52kg |
| Duty Cycle | 60% @ 250A |
| Input Phase | 3 |
To Next Page