BOGBALLE L20 plus User Manual

96 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Operator's Manual

Spreaders

GB

Table of Contents

Default Chapter3
- Table of Contents3
Safety6
- Safety and Protection6
- Legend7
Liability8
Check List9
- Before Every Use10
- Before First Time Use11
- After 5-8 Hours Use11
- After Every Use12
- Useful Hints13
Quick Guide - M60W, M45W, M35W, L20W with CALIBRATOR or ISOBUS14
- Mounting14
- How to Set the Spreader14
- How to Do Headland Spreading14
- How to Do Normal Spreading14
Quick Guide - M45, M35, L20, L15 with CALIBRATOR15
- Mounting15
- How to Set the Spreader15
- How to Do Headland Spreading15
- How to Do Normal Spreading15
Quick Guide - M45, M35, L20, L15 with Mechanical Control16
- Mounting16
- How to Set the Spreader16
- How to Do Headland Spreading17
- How to Do Normal Spreading17
Principle Sketch18
Technical Specifications20
Spread Charts21
- How to Use21
Calibration and Quantity Setting22
- Basic Principle and Definition of Standard Calibration Set Point Value STD22
- Correct Flow-Outlet Setting at High/Low Rates24
- Calibration Procedures/Possibilities M-Line & L-Line25
- MW-Line, L20W with CALIBRATOR ZURF or ISOBUS, Fully Automatic Calibration (FAC)26
- M-Line, L20W, L20 & CALIBRATOR ZURF / Use of Calibration Value STD27
- M-Line & CALIBRATOR ZURF / Use of Calibration Value STD in MAX Flow-Outlet Position28
- M-Line & CALIBRATOR ZURF, Use of STD Calibration Value Via INPUT29
- M-Line, L20W, L20 & CALIBRATOR ZURF, Micro Granular / Small Seeds with Fixed Scale30
- M-Line Manual Calibration on Spreader MC31
- M-Line, L20W, L20 & CALIBRATOR ZURF, Quick Setting Via Spread Chart Value33
- M45, M35, L20 & CALIBRATOR ZURF by Use of S-Indicator Value34
- M45, M35, L20, L15 & CALIBRATOR ICON by Use of S-Indicator Value36
- M45, M35 & CALIBRATOR ZURF/ICON Setting According to Flow-Outlet Position38
- L20, L15 & CALIBRATOR ZURF/ ICON Setting According to Flow-Outlet Position40
- M45, M35, L20, L15 Calibration with S-Indicator in Combination with Hydraulic Control42
Rest-Emptying44
- M-Line44
Normal and Headland Spreading45
- In General45
- To Border45
- From Border46
- Settings for M60W, M45W, M35W, L20W47
  - Normal Spreading47
  - Headland Spreading47
- Settings for M45, M35, L2048
  - Normal Spreading49
  - Headland Spreading49
- Settings for L1553
  - Normal Spreading53
  - Headland Spreading53
Spreader Settings56
- PTO Speed56
- Tilt Angle57
- Working Height - Standard58
- Working Height - Late Application58
- Working Height - Trails59
- Quantity Setting60
- Working Width Setting62
- Spreading Vanes63
Regulation System66
- Connection Rods66
- Outlet Shutters66
Practical Tests67
- Fertiliser Analysis67
Optimize Spreading72
- Normal Spreading72
- Coefficient of Variation72
- Headland Spreading EN13739-173
- To Border73
- Headland Spreading Can be Divided into Three Categories73
- Start and Stop Points at Headlands75
Spreading on Non Rectangular Fields76
- Principle Sketches76
- Controls77
Reduced Working Width80
- Principle Sketches80
  - Mechanical Control and Section Control Standard80
  - Section Control Dynamic80
- Controls81
Maintenance and Care84
- Lubrication84
- Nuts and Bolts84
- Spreading Vanes84
- Normal Maintenance85
- Friction Clutch85
- How to Clean the Friction Clutch85
Corrosion86
Safety - Axle Load87
EC-Declaration of Conformity91
Notes92

Need help?

Do you have a question about the BOGBALLE L20 plus and is the answer not in the manual?

BOGBALLE L20 plus Specifications

General

Brand	BOGBALLE
Model	L20 plus
Category	Spreader
Language	English

Related product manuals

BOGBALLE L20W plus

BOGBALLE L15 base

Preview: BOGBALLE M2

BOGBALLE M Series