BOGBALLE M35W plus - User Manual

96 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operator's Manual

Spreaders

GB

Table of Contents

Default Chapter3
- Table of Contents3
Safety6
- Safety and Protection6
- Legend7
Liability8
Check List9
- Before Every Use10
- Before First Time Use11
- After 5-8 Hours Use11
- After Every Use12
- Useful Hints13
Quick Guide - M60W, M45W, M35W, L20W with CALIBRATOR or ISOBUS14
- Mounting14
- How to Set the Spreader14
- How to Do Headland Spreading14
- How to Do Normal Spreading14
Quick Guide - M45, M35, L20, L15 with CALIBRATOR15
- Mounting15
- How to Set the Spreader15
- How to Do Headland Spreading15
- How to Do Normal Spreading15
Quick Guide - M45, M35, L20, L15 with Mechanical Control16
- Mounting16
- How to Set the Spreader16
- How to Do Headland Spreading17
- How to Do Normal Spreading17
Principle Sketch18
Technical Specifications20
Spread Charts21
- How to Use21
Calibration and Quantity Setting22
- Basic Principle and Definition of Standard Calibration Set Point Value STD22
- Correct Flow-Outlet Setting at High/Low Rates24
- Calibration Procedures/Possibilities M-Line & L-Line25
- MW-Line, L20W with CALIBRATOR ZURF or ISOBUS, Fully Automatic Calibration (FAC)26
- M-Line, L20W, L20 & CALIBRATOR ZURF / Use of Calibration Value STD27
- M-Line & CALIBRATOR ZURF / Use of Calibration Value STD in MAX Flow-Outlet Position28
- M-Line & CALIBRATOR ZURF, Use of STD Calibration Value Via INPUT29
- M-Line, L20W, L20 & CALIBRATOR ZURF, Micro Granular / Small Seeds with Fixed Scale30
- M-Line Manual Calibration on Spreader MC31
- M-Line, L20W, L20 & CALIBRATOR ZURF, Quick Setting Via Spread Chart Value33
- M45, M35, L20 & CALIBRATOR ZURF by Use of S-Indicator Value34
- M45, M35, L20, L15 & CALIBRATOR ICON by Use of S-Indicator Value36
- M45, M35 & CALIBRATOR ZURF/ICON Setting According to Flow-Outlet Position38
- L20, L15 & CALIBRATOR ZURF/ ICON Setting According to Flow-Outlet Position40
- M45, M35, L20, L15 Calibration with S-Indicator in Combination with Hydraulic Control42
Rest-Emptying44
- M-Line44
Normal and Headland Spreading45
- In General45
- To Border45
- From Border46
- Settings for M60W, M45W, M35W, L20W47
  - Normal Spreading47
  - Headland Spreading47
- Settings for M45, M35, L2048
  - Normal Spreading49
  - Headland Spreading49
- Settings for L1553
  - Normal Spreading53
  - Headland Spreading53
Spreader Settings56
- PTO Speed56
- Tilt Angle57
- Working Height - Standard58
- Working Height - Late Application58
- Working Height - Trails59
- Quantity Setting60
- Working Width Setting62
- Spreading Vanes63
Regulation System66
- Connection Rods66
- Outlet Shutters66
Practical Tests67
- Fertiliser Analysis67
Optimize Spreading72
- Normal Spreading72
- Coefficient of Variation72
- Headland Spreading EN13739-173
- To Border73
- Headland Spreading Can be Divided into Three Categories73
- Start and Stop Points at Headlands75
Spreading on Non Rectangular Fields76
- Principle Sketches76
- Controls77
Reduced Working Width80
- Principle Sketches80
  - Mechanical Control and Section Control Standard80
  - Section Control Dynamic80
- Controls81
Maintenance and Care84
- Lubrication84
- Nuts and Bolts84
- Spreading Vanes84
- Normal Maintenance85
- Friction Clutch85
- How to Clean the Friction Clutch85
Corrosion86
Safety - Axle Load87
EC-Declaration of Conformity91
Notes92

Need help?

Do you have a question about the BOGBALLE M35W plus and is the answer not in the manual?

Summary

Safety

Safety and protection

Read Operator's Manual and safety rules before starting.

Check list

Before every use

Checks to perform before operating the spreader.

Quick Guide - M60 W, M45 W, M35 W, L20 W with CALIBRATOR or ISOBUS

1 - Mounting

2 - How to set the spreader

Steps to configure the spreader for operation.

3 - How to do headland spreading

4 - How to do normal spreading

Spread charts

How to use

Calibration and quantity setting

Basic principle and definition of standard calibration set point value STD

Explanation of the standard calibration value and its importance.

MW-line, L20 W with CALIBRATOR ZURF or ISOBUS, fully automatic calibration (FAC)

Procedure for fully automatic calibration with specific controllers.

M45, M35, L20, L15 calibration with S-Indicator in combination with hydraulic control

Calibrating with S-Indicator and hydraulic control.

Normal and headland spreading

Headland spreading

Guidelines for headland spreading, including border spreading categories.

From Border

Settings for M60 W, M45 W, M35 W, L20 W

Settings for M45, M35, L20

Spreader settings

PTO speed

Recommended PTO speeds for normal and headland spreading.

Tilt angle

Quantity setting

Setting the application rate (Kg/Ha) using scale pointer or CALIBRATOR.

Working width setting

Practical tests

Fertiliser analysis

Test with trays

Normal spreading

Optimize spreading

Normal spreading

Optimizing spread pattern using tilt angle for normal spreading.

Headland spreading EN13739-1

Optimizing headland spreading according to EN13739-1 standards.

Headland management

Start and stop points at headlands

Recommendations for start/stop points to achieve optimum overlap.

Spreading on non rectangular fields

Section Control Standard

Section Control Dynamic

Reduced working width

Mechanical control and Section Control Standard

Section Control Dynamic

Controls

Maintenance and care

Lubrication

Normal maintenance

Corrosion

Remember to:

Safety - Axle load

Axle load distribution

Principles of axle load distribution and safety compliance.

Tyre load carrying capacity

Ensuring tractor and tyre load capacities are not exceeded.

BOGBALLE M35W plus Specifications

General

Brand	BOGBALLE
Model	M35W plus
Category	Spreader
Language	English

Related product manuals

BOGBALLE M35 plus

Preview: BOGBALLE M2

BOGBALLE M Series

BOGBALLE L20W plus

BOGBALLE L20 plus

BOGBALLE L15 base