Boge SF 40-2 User Manual

72 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #30 background image

Loading...

Page #30 background image

Produkt.pm6.5 - USA

Page 2.14

Product description

BOGE Operating instructions for S 40-2...S 341 / SF 40-2...SF 220 series screw compressors

Table of Contents

Default Chapter5
- Table of Contents5
General Safety Instructions9
- Safety Instructions for Compressor Operation9
- Safety Instructions for Maintenance and Repair of the Compressor10
- Accident Prevention Regulations10
Introduction12
- Symbols Used12
- Symbols on the Compressor15
- Intended Use15
- Inadmissible Use15
- Transportation Damage16
- Data on the Type Plate16
- Service16
Technical Data17
Function Description23
- Function Principle of the Air End23
- Air Circuit23
- Oil Circuit24
Compressor Control25
- Supply Pressure25
- Operating States25
- Operating Modes25
- Short Operating Times25
Control Devices26
- Operating Pressure Transmitter26
- Proportional Controller (Option for S-Series)26
Safety and Monitoring Devices27
- General27
- Safety Temperature Limiting Device27
- Safety Valve27
- Monitoring the Drive and Fan Motor27
- Rotational Direction Monitoring27
- Safety Pressure Switch (Option)27
- System Pressure Build-Up (Option)27
Water Cooling28
- Serial Connection28
- Parallel Connection28
Cooling Water29
- Water Connection (for Water Cooling)29
- Cooling Water Quality29
Transport31
- General31
- Transport Possibilities31
Compressor Room32
- Installation Surface32
- Fire Protection32
- Admissible Environmental Influences32
- Frost Protection32
- Ventilation32
- Cooling Air Requirement33
- Ventilation Possibilities34
- Condensate Disposal34
Installation35
- General35
- Checking the Delivery Scope35
- Installing the Compressor35
- Connecting the Compressor to the Compressed Air Network35
- Connecting the Cooling Water (Option)36
- Removing the Transport Securing Bolts36
- Activating the Belt Tensioning Device37
- Checking the Oil Level37
Electrical Connection39
Commissioning40
- Checking the Rotational Direction40
- Opening the Stop Valves40
- Checking for Leaks40
- Conduct Trail Run40
- Commissioning Following Extended Stoppages41
General43
General Faults44
Safety Instructions45
General46
- Maintenance through BOGE Service46
- Review of Regular Maintenance Work46
- Maintenance Intervals47
- General Information Concerning the Lubricants Used48
- Disposal of Used Operating Material49
- Spare and Wearing Parts49
Regular Maintenance Work50
- Clean or Change Intake Filter50
- Cleaning the Filter Cartridge50
- Changing the Supply Air Filter Mats (Option)51
- Lubricating the Drive Motor Bearings51
- Drive Motors with Permanent Lubrication51
- Drive Motors with Lubrication Device52
- Servicing Drive Motor53
- Changing the V-Belt54
- Setting GM - Belt Tensioning Device S 40-2 - S 34155
- Checking the Oil Level, Topping up Oil55
- Changing the Oil Filter57
- Changing the Oil Separator58
- Oil Change60
- Flushing the Oil Circuit62
- Cleaning the Compressed Air / Oil Cooling Unit (Air Cooling)62
- Proportional Controller (Option for S-Series)63
- Checking the Safety Valve64
Spare Parts and Optional Equipment65
- List of Spare and Wearing Parts (for Maintenance)65
6.1 Flow Chart67
Part 6: Flow Chart67
- Air Cooled Version, Standard67
- Water Cooled Version, Serial Connection68
- Air Cooled Version, Frequency-Controlled69
Appendix70
List of Maintenance and Service Work70

Questions and Answers:

Need help?

Do you have a question about the Boge SF 40-2 and is the answer not in the manual?

Boge SF 40-2 Specifications

General

Brand	Boge
Model	SF 40-2
Category	Compressor
Language	English

Related product manuals