Bosch AKE 40-19 S - User Manual

Other manuals for Bosch AKE 40-19 S

Original Instructions22 pages

Manual178 pages

Questions and Answers

J
Joyce LloydAug 14, 2025
What to do if my Bosch Chainsaw rips, vibrates, or doesn't saw properly?
- T
  Timothy BushAug 14, 2025
  If your Bosch Chainsaw is ripping, vibrating, or not sawing properly, the issue could be due to several factors. First, check if the chain tension is too loose and adjust it accordingly. Second, the saw chain may be dull, requiring sharpening or replacement. Third, the chain might be worn out, necessitating a replacement. Finally, ensure that the chain teeth are facing in the correct direction; if not, reassemble the chain in the correct direction.
M
Melissa RyanAug 17, 2025
Why is my Bosch Chainsaw chain/guide bar hot?
- E
  eleonardAug 17, 2025
  If the saw chain or guide bar of your Bosch Chainsaw is getting hot, it could be due to a few reasons. First, check if there is enough oil in the reservoir and refill if necessary. Second, the oil passage might be clogged, so clean it. Third, the chain tension could be too high, requiring adjustment. Lastly, a dull saw chain can cause overheating, so sharpen or replace it.
E
elizabethrangelAug 21, 2025
What to do if my Bosch AKE 40-19 S Chainsaw fails to operate?
- A
  Amy CollinsAug 21, 2025
  If your Bosch Chainsaw fails to operate, consider the following potential causes: * The kickback brake may be activated; if so, pull the activation lever back to cover the red dot. * The plug may not be connected; ensure it is properly connected. * The mains socket could be faulty; try using another socket. * The fuse might be blown; replace it. * The extension cable may be damaged; try operating the chainsaw without it.
A
andrew76Aug 25, 2025
What to do if my Bosch Chainsaw operates intermittently?
- S
  Stephanie GonzalezAug 25, 2025
  If your Bosch Chainsaw operates intermittently, the issue might stem from a defective mains cable, which should be checked and replaced if necessary. There could also be an external or internal wiring defect, or a defective On/Off switch.
L
lindachavezAug 27, 2025
Why is the saw chain dry on my Bosch AKE 40-19 S Chainsaw?
- V
  vrodgersAug 27, 2025
  If the saw chain on your Bosch Chainsaw is dry, it's likely due to one of two reasons. Either there is no oil in the reservoir, in which case you should refill it, or the oil passage is clogged, requiring cleaning.
L
Lori MurphyAug 31, 2025
What to do if Bosch Chainsaw rips, vibrates, does not saw properly?
- R
  Robert WallaceAug 31, 2025
  If your Bosch Chainsaw is ripping, vibrating, or not sawing correctly, consider the following: * Adjust the chain tension if it's too loose. * Sharpen or replace the saw chain if it's dull. * Replace the saw chain if it's worn out. * Ensure the chain teeth are facing the correct direction; reassemble if necessary.
A
Antonio VazquezSep 3, 2025
Why is my Bosch Chainsaw saw chain dry?
- S
  Sandra MillerSep 3, 2025
  If your Bosch chainsaw's saw chain is dry, it's likely due to one of two reasons: * There may be no oil in the reservoir. Refill the oil. * The oil passage could be clogged. Clean the oil passage to resolve this.
J
Jacqueline LewisSep 6, 2025
Why does my Bosch Chainsaw operate intermittently?
- M
  Matthew LaneSep 6, 2025
  If your Bosch Chainsaw operates intermittently, it could be due to a defective mains cable. Inspect the mains cable and replace it if necessary. For external or internal wiring defects or a defective On/Off switch, contact your Bosch Service Centre.
S
shermanmichelleSep 10, 2025
What to do if the brake does not stop saw chain of Bosch Chainsaw?
- S
  sarah37Sep 10, 2025
  If the brake on your Bosch Chainsaw isn't stopping the saw chain, it indicates a defective kickback brake or run-down brake. Contact your Bosch Service Centre for assistance.