What to do if the pump for the intelligent dosing system on my Bosch Washer/Dryer is blocked?
To address a blocked pump in the intelligent dosing system of your Bosch Washer/Dryer: First, put the appliance into standby mode. Then, clean the pump unit. Switch the appliance on. If the display appears again after cleaning the pump unit, or the programme cannot be started, call customer service.
What does 'OVERLOAD SCALE' or 'UNDERLOAD SCALE' mean on my Bosch Kitchen Appliances?
If your Bosch Kitchen Appliance displays 'OVERLOAD SCALE' or 'UNDERLOAD SCALE', it means the measurement is outside the scale's range (-990 g to 5000 g). Do not add more than 5000 g or remove more than 990 g of ingredients.
Why is my Bosch Washer/Dryer water pressure low?
Low water pressure in your Bosch Washer/Dryer could be due to a few reasons. Try cleaning the water inflow filter. Also, make sure that the tap is turned on and that the water inlet hose is not kinked or jammed.
What to do if my Bosch Kitchen Appliance switches off during use?
Your Bosch Kitchen Appliance might be switching off during use due to several reasons: * Too much food being processed at once or for too long. To resolve this, turn the rotary switch to 'y', disconnect the mains plug, reduce the processing quantity, and allow the appliance to cool down to room temperature. * The swivel arm was opened. To fix this, turn the rotary switch to 'y', press the release button, and push the swivel arm down until it locks into place. * The bowl or bevel gear (accessory) has become loose. To correct this, turn the rotary switch to 'y', disconnect the mains plug, tighten the bowl by turning it until it stops, and tighten the bevel gear and close the locking lever completely.
What to do if SensorControl Plus on my Bosch Kitchen Appliances cannot be started?
If SensorControl Plus on your Bosch Kitchen Appliance cannot be started and shows “ADD INGREDIENTS” even after adding them, it means the ingredients were added before the scales were activated. Empty the bowl, reselect the program, and only add ingredients after the program is selected and the scales display “0 g” or “0.00 lb” (depending on setting) or “ADD INGREDIENTS”.
What to do if my Bosch Kitchen Appliance displays 'FOR SCALE STOP MACHINE'?
If your Bosch Kitchen Appliance displays 'FOR SCALE STOP MACHINE', it means the scale is switched on while the appliance is running. To resolve this, switch the appliance off and wait until it stops before using the scale.
How to troubleshoot a Bosch Kitchen Appliance when nothing is shown on the display and the illuminated ring is off?
If nothing is shown on the display and the illuminated ring is off, it means the appliance has no power supply. Check the power supply by plugging the mains plug into the mains.
Why Bosch Washer/Dryer spin result is not satisfactory?
If the spin result of your Bosch Washer/Dryer isn't satisfactory and the laundry is too wet, it could be due to a blocked drain pipe or water outlet hose. Clean the drain pipe and the water outlet hose. Also, ensure that the drain pipe or water drain hose isn't caught or jammed. If the unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed, redistribute the laundry in the drum.
How to fix long drying times on my Bosch Washer/Dryer?
If your Bosch Washer/Dryer is taking too long to dry, it could be due to a few factors. If the ambient temperature is greater than 30 °C or there is insufficient air circulation at the appliance's installation location, ventilate the area. Also, if fluff has accumulated in the drum, run the Cottons 90°C programme without any laundry or detergent.
What to do if the Bosch Washer/Dryer programme does not start?
If the programme on your Bosch Washer/Dryer isn't starting, make sure that you have pressed the start button. Also, check that the door is fully closed and that the childproof lock is deactivated. Ensure that the 'Finish in' option is not activated and that no laundry is caught in the door.
General| Oven Type | Built-in |
|---|---|
| Power consumption | 3.6 kW |
| Voltage | 220 - 240 V |
| Installation type | Built-in |
| Timer | Yes |
| Cooling fan | Yes |
| Capacity | 71 liters |
| Frequency | 50/60 Hz |
| Heating system | 3D hot air |
To Next Page