D7024 | Operation and Installation Guide | 12.0 Appendix C: Fire Communicator Reporting Summary
Bosch | 7/05 | 31499J 73
When the Modem IIIa
2
, SIA, or Contact ID reporting formats are used, an additional numeric identifier is
transmitted with system trouble messages to provide a specific indication of the particular fault. This identifier is also
recorded in the History Log. Ta b l e 36 lists the numeric identifiers.
PHONE 1 TROUBLE 52 dd/dd tt:tt ql ACCT aaaa PHONE LINE FAIL
+++ ACCT aaaa PHONE LINE=1
PHONE 1 RESTORE 53 dd/dd tt:tt ql ACCT aaaa PHONE RESTORAL
+++ ACCT aaaa PHONE LINE=1
PHONE 2 TROUBLE 54 dd/dd tt:tt ql ACCT aaaa PHONE LINE FAIL
+++ ACCT aaaa PHONE LINE=2
PHONE 2 RESTORE 55 dd/dd tt:tt ql ACCT aaaa PHONE RESTORAL
+++ ACCT aaaa PHONE LINE=2
SYSTEM TROUBLE 56 dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=ccc
SYSTEM TROUBLE RESTORE 57 dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL
+++ ACCT aaaa SDI=001 COND=ccc
MANUAL TEST 58 dd/dd tt:tt ql ACCT aaaa TEST REPORT
DATA LOST 59 dd/dd tt:tt ql ACCT aaaa COMM FAIL
+++ ACCT aaaa PHONE#=1
EEPROM FAILURE 60 dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=18
EEPROM RESTORAL 61 dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL
+++ ACCT aaaa SDI=001 COND=18
SMOKE POWER FAULT 62 dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=3
SMOKE POWER RESTORE 63 dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL +++ ACCT aaaa
SDI=001 COND=3
REMOTE PROGRAMMING FAIL 66 dd/dd tt:tt ql ACCT aaaa RAM ACCESS FAIL
REMOTE PROGRAMMING SUC-
CESS
67 dd/dd tt:tt ql ACCT aaaa RAM ACCESS OK
Note: dd/dd tt:tt - Date and time; aaaa = Account number; uuu = User ID; zzz = Point; ccc = Numeric identifier
Table 35: Receiver Output
Table 36: Numeric Identifiers
Condition Identifier in
History Log
(reported with
System
Trouble Report)
Condition Identifier in
History Log
(reported with
System
Trouble Report)
Option bus device at address 1 failed. 2 User disabled multiplex bus outputs. 45
Option bus device at Address 2 failed. 3 User disabled dialer. 46
Option bus device at Address 3 failed. 4 User disabled Relay 1. 47
Option bus device at Address 4 failed. 5 User disabled Relay 2. 48
Option bus device at Address 5 failed. 6 User disabled remote relay module 1. 49
Option bus device at Address 6 failed. 7 User disabled remote relay module 2. 50
Option bus device at Address 7 failed. 8 Class “A”, Style 6 wiring failure on MUX
bus.
51
Option bus device at Address 8 failed. 9 MUX bus A (9 to 128) failed. 52
Option bus device at Address 9 failed. 10 MUX bus B (129 to 255) failed 53
Option bus device at Address 10 failed. 11 MUX module processor failure. 54
Option bus device at Address 11 failed. 12 Rremote NAC module 1, output 1 wiring
fault.
55
To Next Page
Loading...
