Bosch D9412GV4 - RPS

D9412GV4/D7412GV4/D7212GV4 | Installation and Operation Guide | 4.0 Installation
Bosch Security Systems, Inc. | 3/12 | F01U266054-01 21
d. Press [NEXT] to see a list of the points
that have not yet been tested. Move
through this list by pressing the [NEXT]
key.
e. To resume the Service Walk Test, press
[ESC]. ## PTS UNTESTED appears.
f. Press [ESC]. ## PTS TO TEST appears.
g. Resume testing points. To end the Service
Walk Test, press [ESC] twice.
6. After the last point is tested, 0 PTS TO TEST
appears. Press [ESC]. The display shows ALL
PTS TESTED briefly before returning to idle
text.
The Service Walk Test, when
performed on a D7412GV4, cannot
display “0 PTS TO TEST” because the
D7412GV4 is physically unable to
connect to the second POPEX Module
(used for Points 129-247).
Automatic time-out returns the system
to idle text: If there is no point or
keypad activity for 20 min., the
Service Walk Test ends automatically.
The keypad returns to idle text.
4.11 Tools Menu
The Tools Menu is collection of configuration and
diagnostic functions that can help resolve various
installation and operation issues with the GV4
Series Control Panels. The menu is accessed
through the Service Menu which is available on
any keypad using [9][9][ENTER].
Access to the Tools Menu requires all of the
following:
 Service User passcode
 All control panels areas are disarmed
 No unacknowledged alarms
 Only one Tools Menu active at a time
 No active RPS sessions including unattended
mode
4.11.1 Programming
Most commonly changed control panel
configuration can be viewed and edited through
this menu. For a complete list of configuration
options refer the GV4 Series Control Panels help
files in RPS for details. For a detailed list of
configuration prompts and their settings, refer to
the D9412GV4/D7412GV4/D7212GV4 Program
Entry Guide (P/N: F01U218312).
4.11.2 Service Bypass
To facilitate system maintenance for service
personnel, a special point bypass option is
provided through this menu to remove any point
from service. The status of points in Service
Bypass can be viewed through the View Service
Bypass menu in the Service Menu. For details in
navigation and operation of this function refer to
the D9412GV4/D7412GV4/D7212GV4 Program
Entry Guide (P/N: F01U218312).
4.11.3 RF Points
With a B820 SDI2 Inovonics Interface Module, the
control panels can support up to 350 RF devices
and up to eight RF Repeater Modules. The RF
Points menu provides the tools necessary to
enroll, remove or replace wireless points. For
details in navigation and operation of these
functions refer to the
D9412GV4/D7412GV4/D7212GV4 Program Entry
Guide (P/N: F01U218312).
The RF Points menu does not affect
the RFIDs learned by the D8125INV
Wireless Interface Module nor the
ISW-D8125CW-V2 Commercial
Wireless Interface Module if installed
on the Zonex bus.
To enroll, remove or replace user
keyfobs refer to the
D9412GV4/D7412GV4/D7212GV4
Owners Manual Supplement (P/N:
F01U245224)
4.11.4 RF Repeaters
With a B820 SDI2 Inovonics Interface Module, the
control panels can support up to 350 RF devices
and up to eight RF Repeater Modules. The RF
Repeaters menu provides the tools necessary to
enroll, remove or replace RF Repeaters. For
details in navigation and operation of these
functions refer to the
D9412GV4/D7412GV4/D7212GV4 Program Entry
Guide (P/N: F01U218312).