English | 17
Bosch Power Tools 2 609 932 590 | (26.6.07)
Technical Data
Noise/Vibration Information
Measured values determined according to
EN 60745.
Typically the A-weighted sound pressure level of
the product is less than 70 dB(A). The noise lev-
el when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Drilling into metal: Vibration emission value
a
h
<2.5 m/s
2
, Uncertainty K=1.5 m/s
2
,
Screwdriving: Vibration emission value
a
h
<2.5 m/s
2
, Uncertainty K=1.5 m/s
2
.
The vibration emission level giv-
en in this information sheet has
been measured in accordance with a standard-
ised test given in EN 60745 and may be used to
compare one tool with another.
The vibration emission level will vary because of
the ways in which a power tool can be used and
may increase above the level given in this infor-
mation sheet. This could lead to a significant un-
derestimate of exposure when the tool is used
regularly in such a way.
Note: To be accurate, an estimation of the level
of exposure to vibration experienced during a
given period of work should also take into ac-
count the times when the tool is switched off
and when it is running but not actually doing the
job. This may significantly reduce the exposure
level over the total working period.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
89/336/EEC, 98/37/EC (until Dec. 28, 2009),
2006/42/EG (from Dec. 29, 2009 on).
19.09.2006, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
Battery Charging (see figure A)
f Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
The Li-ion battery is protected against deep dis-
charging by the “Electronic Cell Protection
(ECP)”. When the battery is empty, the machine
is switched off by means of a protective circuit:
The inserted tool no longer rotates.
Do not continue to press the
On/Off switch after the ma-
chine has been automatically switched off. The
battery can be damaged.
The battery is supplied partially charged. Com-
pletely charge the battery before using your
power tool for the first time. The lithium ion bat-
tery can be charged at any time without reduc-
ing its service life. Interrupting the charging pro-
cedure does not damage the battery.
Cordless Screwdriver GSR 10,8 V-LI
Professional
Article number
3 601 J92 0..
Rated voltage
V= 10.8
No-load speed
rpm 0 – 500
Max. torque for hard/
soft screwdriving appli-
cation according to
ISO 5393 Nm 18/7
Torque adjustment range
Nm 0.9 – 4.8
Max. screw dia.
mm 6
Max. drilling dia.
– Steel
– Wood
mm
mm
8
10
Weight according to
EPTA-Procedure
01/2003
kg 0.8
Please observe the article number on the type plate of your ma-
chine. The trade names of the individual machines may vary.
WARNING
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
WARNING
OBJ_BUCH-405-001.book Page 17 Tuesday, June 26, 2007 2:53 PM
To Next Page
Loading...
