English | 21
Bosch Power Tools 1 609 92A 1GM | (23.6.15)
14 Adjustable fence
15 Bevel lock lever
16 Laser beam outlet
17 Roller
18 Saw blade
19 Dust bag
20 Laser on/off switch (for marking of cutting line)
21 On/Off switch
22 Chip ejector
23 Mounting holes for material clamp
24 Hex key
25 Tilt-protector bar
26 Transport safety-lock
27 Material clamp
28 Spindle lock
29 Indicator for bevel angle
30 Scale for bevel angle
31 Fastening screw for insert plate
32 Fastening screw for tilt-protector bar
33 Hex socket screw for mounting of saw blade
34 Clamping flange
35 Interior clamping flange
36 Wing bolt
37 Threaded rod
38 Clamping lever of the adjustable fence
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Noise Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 96 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 61029-1, EN 61029-2-9, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 23.06.2015
Assembly
Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before starting the operation of the machine
for the first time, check if all parts listed be-
low have been supplied:
– Mitre saw with mounted saw blade
–Dust bag 19
–Material clamp 27
–Hex key 24
– Tilt-protector bar 25 with fastening screws 32
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Mitre Saw PCM 8
Article number
3603M100..
Rated power input
W 1200
No-load speed
min
-1
4800
Laser type
nm
mW
650
<1
Laser class
2
Weight according to
EPTA-Procedure 01:2014 kg 7.9
Protection class
/II
Permissible workpiece dimensions (maximum/minimum) see page 24.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
mm 216
Blade body thickness
mm 1.4–1.8
Max. cutting width
mm 2
Mounting hole diameter
mm 30
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-2324-002.book Page 21 Tuesday, June 23, 2015 8:35 AM
To Next Page
Loading...
