Bosch PSS 200 AC - Tool Specifications; Declaration of Conformity; Dust;Chip Extraction

English–3
2 609 001 137 • 11.5.05
Tool Specifications
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the directives 89/336/EEC,
98/37/EC.
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge
Assembly
Dust/Chip Extraction
Integrated Dust Extraction with Dust Box
(see figures C1–C4)
Attach the dust box 3 onto the outlet piece 7 until it
latches.
To empty the dust box 3, pull off the dust box down-
ward.
Before opening the dust box 3, it is recommended to
loosen the dust from the filter element by gently striking
it against a firm support (as shown in the figure).
Grasp the dust box 3 by the recessed grip, fold the filter
element 8 upward and empty the dust box. Clean the
thin plates of the filter element 8 with a soft brush.
External Dust Extraction (see figure D)
Insert a vacuum hose 9 onto the outlet piece 7. Con-
nect the vacuum hose 9 to a vacuum cleaner. See the
overview for connecting to various vacuum cleaners at
the end of these operating instructions.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum
cleaner.
Replacing the Sanding Sheet
Before any work on the machine itself, pull the
mains plug.
When attaching a new sanding sheet, remove any dust
or debris from the sanding plate 5 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that
the punched holes in the sanding sheet match with the
holes in the sanding plate.
Sanding Sheets with Velcro Backing
(PSS 200 A/PSS 250 A/PSS 250 AE)
(see figure A)
The sanding plate 5 is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 6, free the Velcro
backing of the sanding plate 5 from any debris by tap-
ping against it in order to enable optimum adhesion.
Position the sanding sheet 6 flush alongside one edge
of the sanding plate 5, then lay the sanding sheet onto
the sanding plate and press it against it with a light turn-
ing motion in clockwise direction.
To remove the sanding sheet 6, grasp it at one of the
tips and pull it off from the sanding plate 5.
Orbital sander PSS 190 AC PSS 200 A PSS 200 AC PSS 250 A PSS 250 AE
Article number 3 603 ... C40 1.. C40 0.. C40 1.. C40 2.. C40 2..
Rated power input W 190 200 200 250 250
Preselection of orbital
stroke rate
– – – – z
No-load speed rpm 12000 12000 12000 12000 7000–12000
Orbital stroke rate opm 24000 24000 24000 24000 14000–24000
Orbit diameter mm 2.0 2.0 2.0 2.0 2.0
Sanding sheet dimensions
— Adhesion via
Velcro backing mm – 93 x 185 – 93 x 185 93 x 185
— Attachment via clamping mm 93 x 230 – 93 x 230 93 x 230 93 x 230
Weight according to
EPTA-Procedure 01/2003 kg 1.6 1.6 1.6 1.6 1.6
Protection class
/II /II /II /II /II
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-2 609 001 137-001.book Page 3 Wednesday, May 11, 2005 3:33 PM
mikosoft praha s.r.o. mikosoft praha s.r.o.
mikosoft praha s.r.o. mikosoft praha s.r.o.