English | 21
Bosch Power Tools 2 609 007 738 | (28.10.13)
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Measured sound values
determined according to
EN 60745.
PWS ... 780-125 7500 7800 850-115 850-125 8000
3 603 ... CA2 7.. CA2 4.. CA2 7.. CA2 7.. CA2 7.. CA2 7..
Vibration total values a
h
(tri-
ax vector sum) and uncer-
tainty K determined accord-
ing to EN 60745:
Surface grinding:
a
h
K
Disk sanding:
a
h
K
m/s
2
m/s
2
m/s
2
m/s
2
10.0
1.5
5.0
1.5
10.0
1.5
5.0
1.5
10.0
1.5
5.0
1.5
10.0
1.5
5.0
1.5
10.0
1.5
5.0
1.5
10.0
1.5
5.0
1.5
Angle Grinder PWS ... 680-115 700 7-115 700-115 7000 700-125
Article number
3 603 ... CA2 0.. CA2 0.. CA2 0.. CA2 0.. CA2 0.. CA2 0..
Rated power input
W 701 701 701 701 701 701
Rated speed
min
-1
11000 11000 11000 11000 11000 11000
Grinding disc diameter,
max.
mm 115 115 115 115 115 125
Thread of grinder spindle
M 14 M 14 M 14 M 14 M 14 M 14
Thread length (max.) of
grinder spindle
mm 21 21 21 21 21 21
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
kg 1.7 1.7 1.7 1.7 1.7 1.7
Protection class
/II /II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Angle Grinder PWS ... 700-115 720-115 730-115 750-115 750-125 75-115 7500
Article number
3 603 ... CA2 4 .. CA2 4 .. CA2 4 .. CA2 4 .. CA2 4 .. CA2 4.. CA2 4..
Rated power input
W 701 720 730 750 750 750 750
Rated speed
min
-1
12000 12000 12000 12000 12000 12000 12000
Grinding disc diameter,
max.
mm 115 115 115 115 125 115 125
Thread of grinder spindle
M 14 M 14 M 14 M 14 M 14 M 14 M 14
Thread length (max.) of
grinder spindle
mm 21 21 21 21 21 21 21
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
kg 1.8 1.8 1.8 1.8 1.8 1.8 1.8
Protection class
/II /II /II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-1824-002.book Page 21 Monday, October 28, 2013 2:18 PM
To Next Page
Loading...
