What to do if laundry is stuck in the door of my Bosch WGG244A20 Washer?
If laundry is trapped in the door of your Bosch Washer, open the door again, remove the trapped laundry, close the door, and press the Start/Reload button to start the program.
Why doesn't water run into my Bosch WGG244A20 Washer?
If water isn't running into your Bosch Washer, it could be due to several reasons: * The water tap is closed: Open the faucet. * The water inlet hose is kinked or pinched: Make sure the hose is not kinked. * The detergent drawer is not fully pushed in: Push it in until the symbol goes out.
How to prevent odors from forming in my Bosch WGG244A20?
To prevent odors from forming in the appliance, when you are not using it, leave the door and the detergent drawer open so that any residual water can dry off.
What to do if my Bosch Washer shows error E:30 / -10 or E:30 / -20?
This error can occur due to several reasons: * Low water pressure. * Clogged filters in the water inlet: Clean the filters. * Closed water tap: Open the faucet. * Kinked or pinched water inlet hose: Ensure the hose is not kinked. * Defective water level measurement system: Wait 5 minutes, switch the device off and on. If the error persists, call for service.
What to do if my Bosch WGG244A20 shows error E:36 / -10?
The E:36 / -10 error on your Bosch Washer can be caused by several issues: * Clogged drain pipe or water drain hose: Clean these components. * Kinked or pinched drain pipe or hose: Ensure they are not kinked. * Clogged drain pump. * Water drain hose connected too high: Mount it at a maximum height of 1 meter. * Incorrectly assembled pump cover: Assemble it correctly. * Excessive detergent dosage: Immediately mix a tablespoon of fabric softener with 0.5 liters of water and fill the mixture into the chamber for manual dosing (not for outdoor, sportswear and down textiles). If smart dosing is enabled, decrease the base.
What should I do if my Bosch WGG244A20 detergent dosage is too high?
If the detergent dosage is too high, take these immediate steps: Mix a tablespoon of fabric softener with 0.5 liters of water and fill the mixture into the chamber for manual dosing (not for outdoor, sportswear and down textiles). If smart dosing is enabled, decrease the base. If you dose manually, reduce the amount of detergent for the next wash cycle with the same load.
Why is the display off on my Bosch WGG244A20?
If the display on your Bosch Washer is off, it might be because the energy-saving mode is active. Press any key to exit this mode.
What to do if the detergent drawer is not fully pushed in on my Bosch WGG244A20?
If the detergent drawer is not fully pushed in, push it in until the symbol goes out.
General| Door color | Black |
|---|---|
| Door hinge | Left |
| Cord length | 1.6 m |
| Control type | Rotary, Touch |
| Display type | LED |
| Door opening | Side opening |
| Loading type | Front-load |
| Product color | White |
| Built-in display | Yes |
| Door opening angle | 165 ° |
| Appliance placement | Freestanding |
| Drum capacity | 9 kg |
| Cycle time (max) | 228 min |
| Delay start (max) | 24 h |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Minimum spin speed | 400 RPM |
| Noise level (spin) | 71 dB |
| Noise level (wash) | - dB |
| Overflow protection | - |
| Connected load | 2300 W |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Energy efficiency scale | A to G |
| Water consumption per cycle | 48 L |
| Sustainability certificates | CE, VDE |
Weight and Dimensions| Depth | 590 mm |
|---|---|
| Width | 598 mm |
| Height | 848 mm |
| Weight | 74500 g |
| Door diameter | 320 mm |
| Depth with door open | 1073 mm |
| Depth with door closed | 636 mm |
| Installation compartment height | 850 mm |
Read guide, avoid transit damage, and use as intended.
Ensure proper electrical connection and grounding for safe installation.
Operate device safely, avoid hazards like electric shock and cuts.
Remove packaging, check for damage, and inspect accessories.
Understand installation location needs, including space and stability.
Essential step to prevent damage before first use.
Connect the device to the power supply according to regulations.
Procedures for powering up the washing machine.
How to select and customize wash programs.
Guidelines for loading the drum to prevent creasing.
Steps to initiate a wash cycle.
Rectify minor faults yourself before contacting service.
Specific guidance for addressing display error E:36/-10.
Solutions for error codes related to dosing systems.
Troubleshooting steps for imbalance detection issues.
To Next Page
