BossWeld FX-PRO - User Manual

Questions and Answers

C
Christine GonzalezAug 7, 2025
Why doesn't my BossWeld FX-PRO Welding Accessories filter darken when I strike an arc?
- H
  harrisdavidAug 8, 2025
  Several factors could prevent your BossWeld Welding Accessories filter from darkening when striking an arc. It might be due to: * **Grind Mode being selected:** Adjust the shade from 5-8/9-13. * **Blocked sensors or solar panel:** Ensure the sensors or solar panel are exposed to the weld arc without any obstruction. * **Low sensitivity:** Adjust the sensitivity to the required level. * **Low battery:** If the indicator turns red, replace the lithium batteries.
R
Richard PattersonAug 14, 2025
What to do if my BossWeld FX-PRO Welding Accessories filter remains dark after welding?
- S
  Susan WilliamsAug 14, 2025
  If your BossWeld Welding Accessories filter remains dark after welding, it's likely because the delay is set to maximum. Adjust the delay to the required level to resolve this.
B
blakebrownAug 21, 2025
Why does my BossWeld FX-PRO Welding Accessories filter darken without an arc?
- S
  Sean HarrisonAug 21, 2025
  If your BossWeld Welding Accessories filter darkens without an arc, it's likely that the sensitivity is set too high. Adjust the sensitivity to the required level.
F
fheathAug 30, 2025
How to clean BossWeld Welding Accessories filter to see better?
- J
  Jessica GarciaAug 30, 2025
  If it's difficult to see through the filter of your BossWeld Welding Accessories, the cover lens or filter lens might be dirty. Clean or replace the cover lens, or clean the filter lens to improve visibility.

Summary

Safety Warnings

Arc Rays Can Injure Eyes and Burn Skin

Highlights the dangers of arc rays to eyes and skin, emphasizing protective measures and proper helmet condition.

General Warnings for Welding

Personal Protective Equipment (PPE)

Details essential PPE such as gloves, welding helmets, and safety glasses for welder protection.

Switching Off

Provides instructions on safely switching off welding equipment and handling hot materials.

Fumes & Gases Are Dangerous

Warns about the health hazards of welding fumes and gases, recommending ventilation and respirators.

Work Area When Welding

Avoid Electrical Contact

Advises on electrical safety measures, insulation, and avoiding direct contact with the welding circuit.

Welding Surfaces

Cautionary notes on welding flammable or coated surfaces due to ignition and fume risks.

Work Piece

Emphasizes caution with hot work pieces and the need for gloves when handling welded materials.

Voltage Between Electrode Holders or Torches

Warns about potential dangerous voltage accumulation when multiple machines are connected to a workpiece.

FX-PRO Helmet Specifications

Operation

Headgear Adjustment

Guides on adjusting the helmet's headgear for fit, diameter, height, and viewing angle.

FX-PRO Breakdown

Identifies and lists the various parts of the FX-PRO welding helmet.

Helmet Controls

Shade Control

Explains how to select the appropriate shade level for different welding processes.

Sensitivity Control

Details how to adjust sensitivity based on welding art and ambient light conditions.

Delay Time Control

Describes how to adjust the delay time for filter transition from dark to bright state.

Mode Control

Explains the three modes (Grind, Weld, Cut) and their suitability for different applications.

Maintenance

Front Cover Lens Replacement

Instructions on replacing the front cover lens if it is damaged, cracked, scratched, or dirty.

Inside Cover Lens Replacement

Procedure for replacing the inside cover lens if it becomes damaged or dirty.

Batteries Replacement

Guidance on replacing the helmet's battery when the low voltage indicator turns red.

Cleaning and Storing

Recommendations for cleaning the helmet's components and proper storage procedures.

Trouble Shooting

FX-PRO Parts List

Lists available parts for the FX-PRO welding helmet, including replacement kits and headgear.

Consumable Options

Bossweld 16 Welding Gloves

Details about 16-inch welding gloves available in black and gold cow split leather.

Bossweld Goat Skin Tig Glove

Information on white goat skin TIG gloves with reinforced tipping and Kevlar stitching.

Bossweld Leather Welders Jacket

Description of leather welding jackets with heavy-duty sewing and snap closures.

Bossweld Leather Welding Blanket

Details on chrome leather welding blankets for protecting items from weld spatter.

Other Products In Our Range

Bossweld Spring Handle Chipping Hammer

Details on a chipping hammer used for slag removal and weld bead cleaning.

Bossweld Wire Brush

Information on wooden handled wire brushes for metal cleaning and preparation.

Bossweld Chrome Leather Apron

Description of a chrome leather apron with heavy-duty sewing for protection.

BossWeld FX-PRO Specifications

General

Brand	BossWeld
Model	FX-PRO
Category	Welding Accessories
Language	English