Bostitch MCN250 - User Manual

32 pages

Save Page as PDF

To Next Page

MCN150 / MCN250 / MCN250S

METAL CONNECTOR NAILER

CLAVADORA DE CONECTORES DE METAL

CLOUEUSE À CONNECTEURS MÉTALLIQUES

OPERATION and MAINTENANCE MANUAL

MANUAL DE OPERACIÓN Y DE MANTENIMIENTO

MANUEL D’INSTRUCTIONS ET D’ENTRETIEN

171436REVD 05/07

BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO

UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE

INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,

CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.

ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR

ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE

SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA

HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON

SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.

LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE

ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX

AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI

VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE

CONCESSIONNAIRE BOSTITCH.

STANLEY FASTENING SYSTEMS L.P.

Questions and Answers

S
Shelby ComptonAug 25, 2025
What to do if my Bostitch MCN250 is dry and lacks lubrication?
- C
  Candace CruzAug 26, 2025
  If your Bostitch Power Tool is dry and lacks lubrication, apply BOSTITCH Pneumatic Tool Lubricant.
M
mitchellpaulAug 26, 2025
What should I do if my Bostitch MCN250 Power Tool is dry and lacks lubrication?
- K
  Keith OlsenAug 27, 2025
  If your Bostitch Power Tool is experiencing a lack of power and slow cycling, it may be dry and lack lubrication. Apply BOSTITCH Pneumatic Tool Lubricant.
Y
Yolanda CurryAug 27, 2025
Why does my Bostitch Power Tool have air leaking from the frame or tip?
- N
  Nathan RojasAug 27, 2025
  If your Bostitch Power Tool has an air leak from the frame or tip, the screws on the tip may be loose. Tighten them and check again.
R
Ricky ThomasAug 27, 2025
How to fix air leaking from the frame or deflector of my Bostitch MCN250 Power Tool?
- R
  Rebecca WebbAug 28, 2025
  If your Bostitch Power Tool has an air leak from the frame or deflector, the packing may be damaged. Replace the packing to resolve this issue.
M
Melissa YoungAug 28, 2025
What to do if fasteners are the wrong size for my Bostitch MCN250?
- C
  Christina SmithAug 28, 2025
  If the fasteners are the wrong size for your Bostitch Power Tool, use only the recommended fasteners.
M
Matthew AllenAug 29, 2025
What to do if the screws are loose on the tank or tip of my Bostitch MCN250 Power Tool?
- M
  Michelle MoralesAug 29, 2025
  If the screws are loose on the tank or tip of your Bostitch Power Tool, tighten all the screws.
V
Veronica AlexanderAug 30, 2025
What to do if there is a nail stuck in the drive channel of my Bostitch MCN250 Power Tool?
- A
  Andrew WeissAug 30, 2025
  If there is a nail stuck in the drive channel of your Bostitch Power Tool, disconnect the air supply and clear the jam.
C
cooperjamesAug 23, 2025
What to do if my Bostitch Power Tool has low air pressure?
- A
  Arthur BrooksAug 23, 2025
  If there is low air pressure, check the tool's air supply system.
J
Jennifer GuerreroAug 31, 2025
What to do if the drive valve is worn or leaking on my Bostitch MCN250?
- T
  Tiffany RobertsonSep 1, 2025
  If the drive valve is worn or leaking, replace the drive valve assembly.
N
Nicholas KnightSep 1, 2025
What to do if the trip valve housing is leaking air on my Bostitch Power Tool?
- J
  John ButlerSep 1, 2025
  If the trip valve housing is leaking air, it is likely that the O-ring is cut or cracked. Replace the O-ring.