To Next PageTo Next PageWhy is my Bradford White Defender Safety System 238-48248-00 flashing seven times?
Seven flashes on your Bradford White Water Heater indicate a potential issue. It could be due to flammable vapors being present, the flammable vapor sensor being exposed to excessive moisture or extreme ambient temperatures, or the resettable thermal switch being open. You should check for flammable vapors and ensure proper sensor conditions to resolve this.
What to do if the resettable thermal switch tripped on my Bradford White Defender Safety System 238-48248-00 Water Heater?
If the resettable thermal switch on your Bradford White Water Heater has tripped, ensure there is sufficient combustion air and check for any presence of flammable vapors. These conditions can cause the switch to trip.
How to fix soft lockout with six flashes, three flashes on Bradford White Defender Safety System 238-48248-00?
If your Bradford White Water Heater displays a soft lockout with six flashes followed by three flashes, this could be due to an unstable pilot, a blocked or restricted pilot tube, oxidation build-up on the pilot electrode, wire damage to the pilot assembly, or insufficient combustion air. Inspect the pilot and ensure that there is sufficient combustion air.
How to fix a Bradford White Defender Safety System 238-48248-00 when the LED is not on?
If the LED on your Bradford White Water Heater is not on or flashing, the control power switch may be in the "OFF" position, or the supply voltage may be interrupted. Check the control power switch and ensure that the supply voltage is present.
Why is my Bradford White Defender Safety System 238-48248-00 Water Heater pilot light flashing?
A short flash every second indicates an unstable pilot, a blocked or restricted pilot tube, oxidation build-up on the pilot electrode, or wire damage to the pilot assembly or a bad connection at the gas valve. Inspect and resolve any issues related to the pilot, tube blockage, oxidation, or wiring.
What does eight flashes, three flashes mean on a Bradford White Water Heater?
Eight flashes followed by three flashes on your Bradford White Water Heater indicates a problem with the thermal well. This could be due to damage to the thermal well wires, the thermal well sensor resistance being out of range. You should verify the wiring and sensor conditions and replace parts as necessary.
What does four flashes mean on my Bradford White Water Heater?
Four flashes on your Bradford White Water Heater indicates that the thermal well sensor may be out of calibration or there may be a faulty gas valve. Calibrate the thermal well sensor and check the gas valve for faults.
What causes soft lockout with six flashes, one flash on Bradford White Defender Safety System 238-48248-00 Water Heater?
A soft lockout with six flashes followed by one flash on your Bradford White Water Heater may be caused by an unstable pilot, a blocked or restricted pilot tube, oxidation build-up on the pilot electrode, or wire damage to the pilot assembly or a bad connection at the gas valve. Inspect and resolve any issues related to the pilot, tube blockage, oxidation, or wiring.
What does eight flashes, four flashes mean on a Bradford White Defender Safety System 238-48248-00 Water Heater?
Eight flashes followed by four flashes on your Bradford White Water Heater indicates that you should check the control for wetness or physical damage and reset the control on/off switch. If the error persists, replace the gas control.
General| Brand | Bradford White |
|---|---|
| Model | Defender Safety System 238-48248-00 |
| Category | Water Heater |
| Language | English |
Explains the water heater's system designed to resist ignition of flammable vapors.
Provides critical steps to take if flammable vapors are detected.
Highlights hazards and warranty voidance from not following installation and operating instructions.
Details minimum clearances required for installing the water heater in an alcove.
Crucial safety warnings and actions regarding gas smell and appliance safety before operation.
Step-by-step guide for lighting and operating the water heater, including pilot ignition.
Instructions for safely turning off the gas supply to the appliance.
Guidance on adjusting the thermostat dial for desired temperature settings and energy efficiency.
Warns about scald risk from hot water and recommends mixing valves.
Instructions for visually inspecting the main burner and pilot flames for proper operation.
Illustrates plumbing connections for potable water, showing valves and fittings.
A diagram identifying various water heater components with numerical labels.
A detailed list of water heater parts with their corresponding names and descriptions.
Guidelines and restrictions for piping components used in space heating applications.
Details critical warnings regarding air intake, components, flammable vapor sensor, and error codes.
Caution regarding protecting the setback control and accessory module during installation.
Specifies adherence to electrical codes for wiring and grounding the water heater.
Instructions for installing a flexible power cord, including receptacle requirements and wiring.
Emphasizes disconnecting power before servicing and labeling wires for safety.
Provides a detailed wiring diagram for the water heater's electrical system and components.
Correlates LED status codes with control status and probable causes for system faults.
Lists further LED status codes, control statuses, and their corresponding probable causes.
Details specific faults like Resettable Thermal Switch Tripped and their potential causes.
Explains the initial checks and processes the control performs upon powering up.
Details the step-by-step process of the water heater during a normal heating cycle.
