Bradford White FTCW140

Other manuals for Bradford White FTCW140

Manual4 pages

Questions and Answers

J
Jessica VanceAug 19, 2025
Why is my Bradford White FTCW140 water not hot enough?
- T
  Tiffany JenningsAug 20, 2025
  If the water from your Bradford White Boiler isn't hot enough, try the following: * Check that the temperature setting on the unit isn't set too low. * Make sure the filter in the cold water supply line isn't clogged. * Confirm that the gas supply type is correct for your unit. * Verify the supply and manifold gas pressures are within the specified ranges. * Ensure the water flow sensor with three wires is properly connected on top of the heat exchanger.
M
miranda68Aug 21, 2025
How to fix a Bradford White FTCW140 when the burner does not ignite?
- U
  ugillAug 22, 2025
  If the burner in your Bradford White Boiler doesn't ignite when you open the hot water tap, there are several things to check: * Ensure the ON/OFF button on the Control Panel is ON. * If the Control Panel monitor is blank, verify the power cord is plugged in and the 4A fuses on the main controller are intact. * Confirm the unit is receiving water, as it activates with an inlet water flow exceeding 0 gpm. * Check that the cold and hot water lines aren't reversed. * Ensure both the cold water and gas supply lines are open. * Make sure the water lines aren't frozen.
S
Sean ThompsonAug 25, 2025
What to do if nothing is shown on the Bradford White Boiler control panel?
- S
  Steven LeeAug 25, 2025
  If nothing is showing on the display control panel and no other components of your Bradford White Boiler are operating, consider these checks: * Ensure the service switch and/or circuit breaker to the boiler are turned on. * Confirm there is 120 Volts at the service switch. * Check if the ON/OFF POWER SWITCH (inside the boiler case) is turned on. * Verify there is 120 volts at the line voltage terminal block inside the boiler case. * Inspect the fuse and replace it if necessary.
H
Holly AcevedoAug 26, 2025
Why is my Bradford White FTCW140 water too hot?
- J
  Jessica BrooksAug 26, 2025
  If the water from your Bradford White Boiler is too hot, consider these solutions: * Ensure that the temperature setting on the unit is not too high. * Make sure that the filter in the cold water supply line is not clogged with debris. * Ensure that the gas supply type is correct.
V
Veronica WarrenAug 28, 2025
How to fix hot water temperature fluctuations in my Bradford White FTCW140?
- Y
  yprattAug 28, 2025
  If the hot water temperature from your Bradford White Boiler fluctuates at the tap, try these solutions: * Ensure that the filter in the cold water supply line is clean. * Make sure that the gas supply type is correct. * Check the supply gas pressure is sufficient.
M
Manuel RodriguezAug 29, 2025
What to do if Bradford White FTCW140 Boiler is working but the control panel is blank?
- C
  Cynthia WilliamsAug 29, 2025
  If nothing is displayed on the control panel of your Bradford White Boiler, but the boiler is operating, it may be due to a loss of communication between the control and the display. Try these steps: * Check for loose connections and proper pin alignment/engagement on the Control's plug. * Cycle power off and on using the boiler power switch and check for operation.
X
xrobinsonSep 1, 2025
Why is my Bradford White Boiler making abnormal sounds?
- M
  Michael BerrySep 1, 2025
  If you are hearing abnormal sounds from your Bradford White Boiler during operation: * A leak of combustion gas between the sealed chamber and exhaust tube inside the unit may be the cause; call a qualified service technician for evaluation. * Ensure that the venting termination complies with specifications, as improper venting termination may be the reason. * Check the supply gas pressure is sufficient, as insufficient gas pressure will cause unstable burner flame and noise.
K
Kevin GriffinSep 3, 2025
What does it mean when the temperature rises too quickly on my Bradford White FTCW140?
- V
  Virginia EdwardsSep 3, 2025
  If the temperature rises too quickly in your Bradford White Boiler, it could be because the supply water temperature in the heat exchanger is rising faster than 2°F per second during the first two minutes the burner is on. This condition: * Automatically resets after a few minute delay or using manual reset on control panel. * If you see a 'TEMPERATURE SENSOR' message, follow the procedure for loose connections.
A
Annette HallSep 4, 2025
Why is my Bradford White FTCW140 display blank and the blower running at full speed?
- J
  Jorge FlemingSep 5, 2025
  If nothing is showing on the display control panel and the blower is running at full speed on your Bradford White Boiler: * Check the wiring for a short circuit or incorrect wiring, as the control may not be receiving power. * Check the transformer connection to the control per the wiring diagram and check for 12V output of the transformer.
J
johnsondavidSep 6, 2025
Why does the blower keep running after combustion stops in my Bradford White Boiler?
- B
  brownamySep 6, 2025
  If the blower in your Bradford White Boiler continues to operate after combustion stops, this is normal. The blower keeps operating for 1 minute to vent (exhaust) the flue gas from the chamber once the combustion has stopped.