EasyManua.ls Logo

BRAMIDAN X25 AD - User Manual

Default Icon
49 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating
instructions
Bale press
X-series
Manual no. 7995-014
Version 01-05-2012
USA - English edition
(800) 955-0866
info@BATC-compacts.com
www.BATC-Compacts.com

Table of Contents

Questions and Answers

  • B
    Bryan NavarroAug 10, 2025
    What to do if the start button is flashing on my BRAMIDAN Power Tool baler?
    • G
      gutierrezjimmyAug 10, 2025
      If the start button on your BRAMIDAN Power Tool baler is flashing, it indicates a specific issue: * One flash: The door switch is reporting errors. Open and close the filling door completely. * Two flashes: The emergency stop is activated. Release the emergency stop. * Three flashes: The oil temperature is too high. Wait for the temperature to normalize; this may take a couple of hours. * Four flashes: The motor temperature is too high. Wait for the temperature to normalize; this may take a couple of hours. * Five flashes: Servicing is recommended. Order a service from the dealer. * Six flashes: Other serious errors. Contact the dealer.
  • C
    Cindy WillisAug 18, 2025
    How to fix a BRAMIDAN Power Tool baler that won't start?
    • S
      Stephen NelsonAug 19, 2025
      If your BRAMIDAN Power Tool baler isn't starting, check the following: * Ensure the cable is connected to the supply network. * Verify the repair switch is set to "1" or "ON". * Make sure the emergency stop is released. * Replace the fuse with one of the same amperage. If the problem continues, call for service.
  • R
    Robert MirandaAug 29, 2025
    Why is my BRAMIDAN X25 AD baler so noisy?
    • Z
      Zachary BlevinsAug 29, 2025
      If your BRAMIDAN Power Tool baler is making excessive noise, the following actions may resolve the issue: * Replace the wear blocks. * Replace the release roller. * Remove any foreign objects that may be causing the noise.

Summary

Personal Safety

Operator Responsibilities and Authorization

General Safety Precautions

Covers safe operation, working area, safety features, and binding materials to prevent hazards.

Use and Function

Material Compatibility and Restrictions

Lists compatible waste types and materials that must not be compressed to avoid damage or hazards.

Transport

Lashing Procedures

Center of Gravity and Safe Transport

Highlights the baler's high center of gravity and precautions for safe transportation, including tilt angles.

Forklift Truck Transport Guidelines

Crane Transport Procedures

Installation

Electrical Connection Requirements

Details checking supply network, motor phases, and voltage for safe electrical connection.

Single-Phase Motor Connection

Three-Phase Motor Connection

Three-Phase Motor without Phase Inverter

Operating Principles

Power Interruption and Reset

Emergency Stop and Start Button Functions

Explains the operation of the emergency stop and start buttons for cycle control and safety.

Two-Hand Control and Ejection Blocking

Details the two-hand control mechanism and reasons for blocked bale ejection.

The Operating Panel

Control Panel Description and Layout

Details the components and layout of the operating panel for B-series and X-series models.

Push Button Light Signal Meanings

Push Button Functions and Operations

Explains the functions of compression, binding, premature finishing, and occasional platen parking.

Filling and Compression

Waste Distribution and Compression Process

Finishing and Cancelling Premature Bale Formation

Ejecting the Bale

Pre-Ejection Checks and Safety

Performing Bale Ejection

Maintenance

Safety Precautions for Maintenance

Daily and Weekly Checks

Biannual and Annual Checks

Troubleshooting

Basic Start-Up Issues

Addresses common problems preventing the baler from starting, such as connection, repair switch, and emergency stop.

Start Button Flashing and Noise Issues

Guides on interpreting start button flashes and troubleshooting baler noise issues.

Ejection and Leakage Problems

Provides solutions for issues with bale ejection and hydraulic oil leakage.

Checklist for Safety Check

Overview of Safety Check Items

Introduces the annual safety check process and identifies key components for inspection.

Checking Electrical and Control Systems

Guides on checking cable, socket, repair switch, emergency stop, and two-hand control functions.

Checking Switches and Sensors

Details checks for door switches, top switches, and AD door control systems.

Final Checks and Documentation

BRAMIDAN X25 AD Specifications

General IconGeneral
BrandBRAMIDAN
ModelX25 AD
CategoryPower Tool
LanguageEnglish

Related product manuals