BRAMIDAN X30 - User Manual

Operating
instructions
Bale press
X-series
Manual no. 7995-014
Version 01-05-2012
USA - English edition
(800) 955-0866
info@BATC-compacts.com
www.BATC-Compacts.com

Summary

Personal Safety Precautions

Authorized Personnel and Training

Only authorized employees may operate, inspect, or maintain the baler.

Transport and Center of Gravity Safety

Cautions about the baler's high center of gravity during transport.

Safe Work Area and Equipment

Keep work area clear; ensure safety features are functional; use proper binding materials.

Handling Binding Materials

Caution when handling steel wire and wearing gloves for protection.

Material and Hydraulic Fluid Safety

Prohibits certain materials and outlines precautions for hydraulic oil contact.

Baler Use and Material Compatibility

Suitable Waste Types

Lists compatible waste materials for B-series and X-series balers.

Material Restrictions and Placement

Prohibits specific waste types and specifies horizontal placement of items.

Key Operational Safety Features

Highlights emergency stop, indicator lights, door interlocks, and ejection safety mechanisms.

Transport and Securing the Baler

Lashing Procedures for Transport

Instructions on correctly lashing the baler using brackets or oval holes.

Center of Gravity and Lifting Angles

Critical information on the baler's high center of gravity and maximum tilt angle (8°).

On-Side Transport Precautions

Steps for safely transporting the baler on its side, protecting the oil tank.

Forklift Transport Safety Guidelines

Advice on using forklifts to avoid damage and maintain safe operating height.

Crane Lifting and Moving Procedures

How to lift the baler with a crane and move an installed unit safely.

Installation Environment and Requirements

Installation Site Considerations

Placement in residential/industrial settings, noise, and vibration management.

Indoor vs. Outdoor Installation

Guidelines for indoor placement and outdoor protection for extended lifespan.

Clearances and Workspace Setup

Required clearances for door operation and maintaining a safe, clear working area.

Electrical Connection Procedures

Single Phase Motor Connection

Ensuring secure connection and accessible power interruption for single-phase motors.

Three Phase Motor Connection and Rotation Check

Connecting three-phase motors and verifying correct clockwise rotation for pump.

Three Phase Wiring Without Phase Inverter

Instructions for qualified electricians on wiring three-phase motors without a phase inverter.

Baler Operating Principles and Controls

Power Interruption and Reset Procedures

Emergency Stop and Start Button Functions

Two-Hand Control and Ejection Safety

Troubleshooting Binding Issues

Operating Panel Layout and Indicators

Control Panel Button Identification (B-Series)

Control Panel Button Identification (X-Series)

Button Light Signal Meanings

Push Button Operation Details

Explains functions of compression, binding, premature finishing, and occasional platen parking.

Filling and Compressing the Bale

Pre-Operation Safety Checks

Loading and Distributing Waste

Compression Cycle Initiation

Finishing Bale Prematurely

Bale Binding with Cords or Straps

Cords;Straps Binding Steps

Bale Binding with Steel Wire

Tightening and Securing Steel Wire

Bale Ejection Process and Checks

Pre-Ejection Safety and Door Checks

Ejection Mechanism and Power Disconnection

Performing the Bale Ejection

Executing bale ejection using two-hand control and ensuring operator safety.

Operator Safety During Ejection

Maintenance and Safety Procedures

Mandatory Maintenance Safety Rules

Disconnect power, use safety gear, and employ authorized personnel for all maintenance.

Daily and Weekly Inspection Tasks

Biannual Oil Level Monitoring

Annual Service and Safety Checks

Troubleshooting Common Issues

Baler Fails to Start

Start Button Flashing Error Codes

Ejection and Leakage Troubleshooting

Annual Safety Inspection Checklist

Checklist Purpose and Procedure

Cable, Switch, and Emergency Stop Checks

Two-Hand Control Operation Test

Door Switch and Top Switch Verification

BRAMIDAN X30 Specifications

General

Brand	BRAMIDAN
Model	X30
Category	Power Tool
Language	English