Why are battery segments in the display skipped on my Braun Electric Shaver as the battery decreases?
Skipped battery segments on your Braun Electric Shaver indicate that the foil and cutter are likely worn, causing the shaver to require more power. Replacing the Foil & Cutter cassette and regularly oiling the shaving system, especially after cleaning with water, should improve this.
How to get rid of the unpleasant smell from Braun Electric Shaver head?
To address an unpleasant smell from the shaver head of your Braun Electric Shaver, ensure that when cleaning the shaver head with water, you only use hot water and occasionally some liquid soap (without abrasive substances). Also, remove the Foil & Cutter cassette to allow it to dry properly.
How to reset replacement symbol on Braun Electric Shaver?
To reset the replacement symbol light on your Braun Electric Shaver after changing shaving parts, push the reset button for at least 3 seconds.
What to do if cleaning doesn't start when pressing the start button on my Braun Rechargeable shaver?
If the cleaning cycle doesn't start when you press the start button on your Braun Rechargeable shaver, consider the following: 1. Ensure the shaver is correctly placed in the Clean&Renew station, with the shaver's contacts aligned with the station's contacts. 2. Check if the cleaning cartridge has sufficient cleaning fluid; a red light indicates it needs replacement. Insert a new cleaning cartridge if necessary. 3. Verify the appliance isn't in standby mode. Press the start button again to initiate cleaning.
Why does my Braun Electric Shaver turn off with a fully charged battery?
If your Braun Electric Shaver turns off even with a fully charged battery, it's likely due to worn foil and cutter, demanding more power than the motor can provide. Replace the Foil & Cutter cassette and regularly oil the shaving system, particularly after cleaning it with water only.
Why has my Braun Rechargeable shaver's battery life decreased significantly?
A significant drop in battery performance in your Braun Rechargeable shaver can occur due to: 1. Worn foil and cutter, which increases the power needed for each shave. To resolve this, renew the Foil & Cutter cassette. 2. Regular cleaning of the shaver head with water without lubrication. If you clean the shaver with water, apply a drop of light machine oil on top of the foil once a week.
Why has my Braun Rechargeable shaver's shaving performance decreased?
A drop in shaving performance of your Braun Rechargeable shaver can occur for several reasons: * The foil and cutter may be worn, requiring replacement. * The personal setting of shaving performance may have been changed; consider using the green (intensive) setting for a faster shave. * The shaving system could be clogged. To resolve this, soak the Foil & Cutter cassette in hot water with a drop of dish liquid, rinse it thoroughly, tap it out, and apply a drop of light machine oil once it's dry.
Why is the shaver head of my Braun Electric Shaver damp?
If your Braun Electric Shaver head is damp, it could be due to a few reasons: either the drying time after automatic cleaning was too short, the drain of the Clean&Renew station is clogged, or the cleaning cartridge has been used for quite a while. To address this, clean the shaver directly after shaving to allow enough time for drying. Also, clean the drain with a wooden toothpick and regularly wipe the tub clean. If the cleaning cartridge has been used for a long time, the ethanol/isopropanol proportion has decreased while the oil proportion has increased; remove residue with a cloth.
Why are battery segments skipped on my Braun Electric Shaver?
If the battery segments in the display of your Braun Electric Shaver are skipped as the battery capacity decreases, it usually means the foil and cutter are worn, requiring more power for each shave. You should replace the Foil & Cutter cassette. Regularly oiling the shaving system, especially after cleaning with water only, can also help.
Why is there increased consumption of cleaning fluid in my Braun 5697 Electric Shaver's cleaning station?
Increased cleaning fluid consumption in your Braun Electric Shaver's cleaning station is often due to a clogged drain. Clean the drain with a wooden toothpick and regularly wipe the tub clean to resolve this.
General| Brand | Braun |
|---|---|
| Model | 5697 |
| Category | Electric Shaver |
| Language | English |
To Next Page
