How to prevent increased consumption of cleaning fluid in my Braun Electric Shaver?
To address increased consumption of cleaning fluid in your Braun Electric Shaver's Clean & Charge station, start by cleaning the drain with a wooden toothpick if it's clogged. Additionally, regularly wipe the tub clean.
Why is my Braun Electric Shaver shaving performance dropped significantly?
If the shaving performance of your Braun Electric Shaver has significantly declined: * The foil and cutter may be worn. If so, renew the Foil & Cutter cassette. * The shaving system could be clogged. To resolve this, soak the Foil & Cutter cassette in hot water with a drop of dish liquid, then rinse it thoroughly, tap it out, and once dry, apply a drop of light machine oil to the foil.
What to do if cleaning does not start on Braun 5793?
If cleaning doesn't start when you press the start button on your Braun Electric Shaver, check the following: * Ensure the shaver is properly placed in the Clean & Charge Station, pushed to the rear so that the contacts align. * Verify the cleaning cartridge contains sufficient cleaning fluid. If the display blinks red, insert a new cleaning cartridge and press the start button again. * The appliance might be in stand-by mode. Press the start button again to initiate cleaning.
Why does my Braun 5793 battery performance dropped significantly?
If you notice a significant drop in battery performance of your Braun Electric Shaver, there are a couple of potential reasons: * The foil and cutter may be worn, requiring more power for each shave. Renew the Foil & Cutter cassette. * If you regularly clean the shaver head with water but don't lubricate it, apply a drop of light machine oil on top of the foil once a week for lubrication.
Why is my Braun Electric Shaver battery performance dropped significantly?
A significant drop in battery performance of your Braun Electric Shaver can occur if the foil and cutter are worn, requiring more power for each shave. Renewing the Foil & Cutter cassette can resolve this issue. Also, regularly cleaning the shaver head with water but not lubricating it can cause this problem. If you clean the shaver with water, apply a drop of light machine oil on top of the foil once a week for lubrication.
What to do if my Braun 5793 Electric Shaver cleaning does not start when pressing the start button?
If the cleaning cycle doesn't start when you press the start button on your Braun Electric Shaver's Clean & Charge Station, make sure the shaver is correctly placed in the station, pushed to the rear so that the contacts align. If the cleaning cartridge does not contain sufficient cleaning fluid (display blinks red), insert a new cleaning cartridge and press the start button again. Also, ensure that the appliance is not in stand-by mode, and if so, press the start button again.
What to do if my Braun 5793 shaving performance dropped significantly?
If you notice a significant drop in shaving performance with your Braun Electric Shaver, it could be due to worn foil and cutter. Consider renewing the Foil & Cutter cassette. Another possible cause is a clogged shaving system. To resolve this, soak the Foil & Cutter cassette in hot water with a drop of dish liquid, then rinse it thoroughly, tap it out, and apply a drop of light machine oil once it's dry.
Why does my Braun Electric Shaver have an unpleasant smell?
An unpleasant smell from your Braun Electric Shaver head can occur if the shaver head is cleaned with water. When cleaning the shaver head with water only use hot water and from time to time some liquid soap (without abrasive substances). Remove Foil & Cutter cassette to let it dry. Also, if the cleaning cartridge is in use for more than 8 weeks, change the cleaning cartridge at least every 8 weeks.
Why my Braun Electric Shaver does not charge completely and keeps blinking?
If your Braun Electric Shaver does not charge completely and keeps blinking, the ambient temperature might be out of the valid range. The recommended ambient temperature for charging is 5 °C to 35 °C.
What to do if Braun Electric Shaver head is damp?
If the shaver head of your Braun Electric Shaver is damp after cleaning: * The drying time after automatic cleaning may have been too short. Wait until the drying process is completed. * The drain of the Clean & Charge station might be clogged. Clean the drain with a wooden toothpick.
Describes potential for death or severe injury.
Identifies and describes the parts of the shaver.
Safety instructions for charging the appliance.
Safety warnings for operating the shaver correctly.
Advice for achieving an optimal shave.
Detailed steps for cleaning the shaver under running water.
Safety warnings for using the alcohol cleaning system.
Identifies and explains parts of the cleaning system.
Solutions for common shaver operational problems.
Details about the warranty card and its contents.
How to request repair service for the product.
Phone numbers and websites for customer service and repair.
Warnings regarding the power supply, charging stand, and cleaning station.
How to connect and charge the shaver.
Detailed steps for cleaning the shaver with water.
Overview of the cleaning, charging, lubricating, and drying station.
Solutions for when the shaver won't turn on.
Troubleshooting issues with charging not starting.
Solutions for the cleaning station not starting.
General| Model | 5793 |
|---|---|
| Series | Series 5 |
| Wet & Dry | Yes |
| Charging Time | 1 Hour |
| Cordless Use | Yes |
| Corded Use | No |
| Cleaning Station | No |
| Precision Trimmer | Yes |
| Auto Sensing Motor | Yes |
| Travel Lock | Yes |
| Waterproof | Yes |
| Shaver Type | Foil |
| Battery Type | Lithium-ion |
To Next Page
