To Next PageTo Next PageWhy are battery segments in the display skipped when battery capacity decreases on my Braun 7898cc Electric Shaver?
Skipped battery segments often indicate that the foil and cutter are worn, requiring more power for each shave. Consider renewing the Foil & Cutter cassette and regularly oiling the shaving system, particularly if you primarily clean it with water.
What to do if the cleaning cycle does not start when pressing the start button on my Braun Electric Shaver?
If cleaning doesn't start when you press the start button, check the following: 1. Ensure the shaver is correctly placed in the Clean&Renew station, with the shaver's contacts aligned with those in the station. 2. Verify that the cleaning cartridge has enough cleaning fluid (the display will light red if it doesn't). If needed, insert a new cleaning cartridge. 3. Make sure the appliance is not in stand-by mode. If it is, press the start button again.
What to do if cleaning does not start when pressing the start button on my Braun Electric Shaver?
If the cleaning cycle doesn't start when you press the start button on your Braun Electric Shaver, consider these possibilities: * The shaver might not be properly placed in the Clean&Renew station. Ensure the shaver's contacts align with the station's contacts. * The cleaning cartridge may not contain enough cleaning fluid. If the display lights red, insert a new cleaning cartridge. * The appliance could be in stand-by mode. Press the start button again.
Why is there increased consumption of cleaning fluid in my Braun 7898cc Electric Shaver's cleaning station?
Increased consumption of cleaning fluid in your Clean&Renew station is often due to a clogged drain. Clean the drain with a wooden toothpick and regularly wipe the tub clean to resolve this issue.
Why is the shaver head of my Braun Electric Shaver damp?
A damp shaver head can result from a few issues: 1. The drying time after automatic cleaning might be too short. Try cleaning directly after shaving to allow ample drying time. 2. The Clean&Renew station's drain could be clogged. Clean it with a wooden toothpick and regularly wipe the tub clean. 3. The cleaning cartridge might have been used for too long, decreasing the ethanol/isopropanol proportion while increasing the oil proportion. Remove any residue with a cloth.
What to do if my Braun 7898cc head is damp?
A damp shaver head on your Braun Electric Shaver can occur for a few reasons: * Insufficient drying time after automatic cleaning. Try cleaning directly after shaving to allow more drying time. * A clogged Clean&Renew station drain. Clean the drain with a wooden toothpick and regularly wipe the tub clean. * Prolonged use of the cleaning cartridge. The ethanol/isopropanol proportion decreases while the oil proportion increases. Remove residue with a cloth.
How to reset replacement indicator on Braun Electric Shaver?
If the replacement symbol lights up on your Braun Electric Shaver even after changing shaving parts, the reset button likely hasn't been pushed. Push the reset button for at least 3 seconds to reset the counter.
Why does my Braun Electric Shaver head have an unpleasant smell?
An unpleasant smell from your Braun Electric Shaver head may be caused by: * Cleaning the shaver head with water. When cleaning the shaver head with water, use only hot water and occasionally some liquid soap (without abrasive substances). Remove the Foil & Cutter cassette to let it dry. * The cleaning cartridge has been in use for more than 8 weeks.
Why has the battery performance of my Braun Electric Shaver dropped significantly?
A significant drop in battery performance can occur if the foil and cutter are worn, requiring more power for each shave. Renewing the Foil & Cutter cassette may resolve this. Also, if you regularly clean the shaver with water, applying a drop of light machine oil on top of the foil can help.
What to do if shaving parts have been changed recently but replacement symbol lights up on Braun Rechargeable shaver?
If the replacement symbol lights up on your Braun Rechargeable shaver even after changing the shaving parts, it means the reset button hasn't been pushed. Push the reset button for at least 3 seconds to reset the counter.
General| Brand | Braun |
|---|---|
| Model | 7898cc |
| Category | Electric Shaver |
| Language | English |
