Braun 8390CC - User Manual

Questions and Answers

M
Maureen GarciaAug 18, 2025
Why is my Braun Electric Shaver not charging?
- J
  Jesse CummingsAug 18, 2025
  There could be several reasons why your Braun Electric Shaver isn't charging: 1. Sometimes charging is delayed, especially after long storage. Give it a few minutes to start automatically. 2. The ambient temperature may be outside the recommended range of 5 °C to 35 °C. 3. The power supply might not be properly connected to the shaver; ensure it snaps in. 4. If using the Clean & Charge Station, make sure the shaver's contacts align with the station's contacts.
R
rwalterAug 20, 2025
What to do if cleaning doesn't start on my Braun Electric Shaver?
- B
  brittanygomezAug 21, 2025
  If the cleaning cycle isn't starting on your Braun Electric Shaver, check these: 1. Ensure the shaver is correctly placed in the Clean & Charge Station, pushed to the rear so the contacts align. 2. Make sure the cleaning cartridge has enough cleaning fluid (if the display blinks red, it needs replacing). Insert a new cartridge and press the start button again. 3. The appliance might be in stand-by mode. Press the start button again to initiate cleaning.
E
edward84Aug 23, 2025
Why does my Braun 8390CC Electric Shaver head smell bad?
- A
  Alex MooreAug 23, 2025
  An unpleasant smell from your Braun Electric Shaver head may be due to: 1. Cleaning the shaver head with water improperly. Use only hot water and occasionally a bit of liquid soap (without abrasive substances). Remember to remove the Foil & Cutter cassette and let it dry. 2. Using the cleaning cartridge for too long. Replace the cleaning cartridge at least every 8 weeks.
M
Michael GrantAug 26, 2025
Why is my Braun 8390CC Electric Shaver using so much cleaning fluid?
- R
  robert59Aug 26, 2025
  Increased consumption of cleaning fluid in your Braun Electric Shaver's Clean & Charge station could be due to a clogged drain. Clean the drain with a wooden toothpick and regularly wipe the tub clean.
J
Jessica SantosAug 27, 2025
Why is my Braun 8390CC Electric Shaver head damp?
- A
  Ashley SmithAug 27, 2025
  A damp shaver head on your Braun Electric Shaver can occur because: 1. The drying time after automatic cleaning was too short. Clean directly after shaving to allow enough drying time. 2. The drain of the Clean & Charge station is clogged. You should clean the drain with a wooden toothpick.
S
Susan Carter MDAug 30, 2025
Why is my Braun 8390CC consuming cleaning fluid so fast?
- A
  adamandersonAug 30, 2025
  Increased consumption of cleaning fluid in your Braun Electric Shaver's Clean & Charge station may indicate that the drain is clogged. Try cleaning the drain with a wooden toothpick.
R
robinsonbenjaminSep 1, 2025
Why does my Braun Electric Shaver not charge fully and keep blinking?
- H
  hallvanessaSep 1, 2025
  If your Braun Electric Shaver isn't fully charging and continues to blink, the ambient temperature might be outside the recommended range. The ideal temperature for charging is between 5 °C and 35 °C.
J
James OlsenSep 3, 2025
How to unlock Braun 8390CC?
- J
  John StewartSep 3, 2025
  To unlock your Braun Electric Shaver, unplug the shaver and then press the on/off button for 5 seconds.
G
Gabrielle DeckerSep 6, 2025
Why has my Braun Electric Shaver shaving performance dropped significantly?
- C
  Chelsea MorrisSep 6, 2025
  If your Braun Electric Shaver's shaving performance has significantly declined, the foil and cutter may be worn and need replacement. Alternatively, the shaving system might be clogged. To resolve this, soak the Foil & Cutter cassette in hot water with a drop of dish liquid, then rinse it thoroughly and tap it out. Once dry, apply a drop of light machine oil to the foil.
M
Michael DillonSep 8, 2025
Why has my Braun Electric Shaver battery performance dropped significantly?
- C
  curtisbrianSep 8, 2025
  If your Braun Electric Shaver's battery performance has dropped significantly, it could be because the foil and cutter are worn, requiring more power for each shave, so you should renew the Foil & Cutter cassette. Also, if you regularly clean the shaver head with water but don't lubricate it, apply a drop of light machine oil on top of the foil once a week for lubrication.