Why does my Braun IS 7055 make intermittent vibrating noises?
If your Braun Iron emits an intermittent noise associated with vibrations, it's because water is being pumped into the boiler. This is normal and no action is needed.
What to do if my Braun Iron doesn't switch on?
If your Braun Iron does not switch on, it might not be properly plugged into a mains socket. Make sure the appliance is correctly connected and press the On/Off button.
Why does my Braun Iron leak water from the soleplate?
If you notice water drops from the holes in the bottom of the soleplate of your Braun Iron, it's likely due to water condensation inside the tubes. This usually happens when steam is used for the first time or after a long period of inactivity. To resolve this, press the steam button several times away from the ironing board to eliminate any cold water from the steam circuit.
Why is the steam setting icon on, but no steam comes out of my Braun Iron?
If the steam setting icon is permanently on but there is no steam emission from the soleplate of your Braun Iron, the water tank float may be locked, or the water tank is not correctly inserted. To fix this, turn off and unplug the appliance. Remove and empty the water tank, rinse it out, and refill it. Reinsert the water tank and wait until the appliance has cooled down for at least 2.5 hours, then try again. If the problem persists, contact an authorized Braun Customer Service.
Why is steam or water leaking from the closure of my Braun IS 7055?
If steam or water is coming out from the closure of your Braun Iron, the closure is likely not tightened properly. Switch off the appliance, unplug it, and let it cool down for at least 2.5 hours. Unscrew the closure and screw it back on properly. Note that some water can escape when you unscrew the closure.
Why does my new Braun IS 7055 smell or smoke when I turn it on?
If you notice smoke or smell the first time your Braun Iron is turned on, it is because some parts have been treated with sealer/lubricant which evaporates the first time the iron heats up. This is normal and will stop when you have used the iron a few times. If the smoke/smell is still present after turning off the appliance, contact an authorised Braun Customer Service.
What to do if my Braun IS 7055 Iron emits a continuous noise associated with vibrations?
If your Braun Iron emits a continuous noise associated with vibrations, it indicates a system error. Unplug the appliance from the mains and contact an authorised Braun Customer Service.
Why is my Braun IS 7055 leaking brown fluid?
If brown colored fluid leaks from the soleplate of your Braun Iron, it is because chemical water softeners or additives have been poured into the water tank. Never pour such products into the water tank. Clean the soleplate with a damp cloth and rinse the boiler.
Why does my new Braun IS 7055 Iron smoke or smell when I turn it on for the first time?
If you notice smoke or a smell the first time you turn on your Braun Iron, it's normal. Some parts have been treated with sealer/lubricant which evaporates the first time the iron heats up. This should stop after you've used the iron a few times. If the smoke/smell persists after turning off the appliance, contact an authorized Braun Customer Service.
What to do if the icon doesn't reset after refilling the water tank on my Braun IS 7055?
If the icon on your Braun Iron doesn't reset after refilling the water tank, it could be due to a water float malfunction or incorrect positioning of the water tank. Try emptying the water tank, rinsing it out, and refilling it. Also, ensure the water tank is positioned correctly.
General| Power | 2400 W |
|---|---|
| Steam output | 50 g/min |
| Water tank capacity | 300 ml |
| Cord length | 2.5 m |
| Type | Steam Iron |
| Vertical steam | Yes |
| Pressure | 5 bar |
| Soleplate | Eloxal |
To Next Page
