Bredel APEX35 - User Manual

Questions and Answers

A
Amy LopezAug 14, 2025
How to troubleshoot a Bredel APEX35 that fails to operate?
- R
  Rebecca ChanAug 15, 2025
  If your Bredel Industrial Equipment fails to operate, there are several potential causes to investigate: * **No voltage:** Ensure the power supply switch is turned on and that the electrical supply is available at the pump. * **Stalled rotor:** Check if the pump is stalled due to incorrect hose fitting. Also, verify the VFD settings, if applicable. * **Lubricant level monitoring system activation:** Determine whether the lubricant level monitoring system has stalled the pump. Check the system's functionality and the lubricant level.
A
adamholmesAug 21, 2025
What to do if my Bredel APEX35 has low capacity or pressure?
- G
  Gina JohnsAug 21, 2025
  If your Bredel Industrial Equipment exhibits low capacity or pressure, consider the following: * **Shut-off valve:** Ensure the shut-off valve in the suction line is fully open. * **Hose condition:** Check for hose rupture or wear and replace the hose if necessary. * **Blockage:** Clear any blockages in the suction line and ensure sufficient fluid is available. * **Connections:** Verify that all connections are correctly mounted and tightened to prevent air suction.
C
Catherine SmithAug 25, 2025
How to extend the hose life of my Bredel APEX35 Industrial Equipment?
- M
  Mitchell DunnAug 25, 2025
  To maximize the hose life of your Bredel Industrial Equipment, keep in mind these points: * **Chemical attack:** Verify the hose material's compatibility with the fluid being pumped. Consult your Bredel representative for correct hose selection. * **Pump speed:** Reduce pump speed to minimize wear. * **Discharge pressures:** Ensure that the discharge line is not blocked, the shut-off valves are fully opened, and the pressure relief valve functions properly. Maximum working pressure 800 kPa (116 psi). * **Product temperature:** Consult your Bredel representative for correct hose selection. * **Pulsations:** Restructure the discharge and inlet conditions.
S
Scott FryeAug 27, 2025
Why is my Bredel Industrial Equipment pump and pipework vibrating?
- B
  Brian JuarezAug 27, 2025
  Vibration in your Bredel Industrial Equipment pump and pipework can stem from: * **Insecure lines:** Check and secure the suction and discharge lines. * **High pump speed:** Reduce pump speed, especially with long lines or high relative density. Reduce the line lengths on both suction and discharge where possible. Consult your Bredel representative for a recommendation. * **Narrow diameter:** Increase the diameter of the suction/discharge lines if they are too narrow.
L
llawrenceAug 31, 2025
What should I do if the hose is pulled into the Bredel APEX35 Industrial Equipment pump?
- H
  Heather BushAug 31, 2025
  If the hose is being pulled into the Bredel Industrial Equipment pump, consider these factors: * **Insufficient lubricant:** Add extra lubricant to the pumphead. Refer to § 8.4. * **Incorrect lubricant:** Consult your Bredel representative for the correct lubricant, ensuring it's Bredel Genuine Hose Lubricant. * **High inlet pressure:** Reduce the inlet pressure if it exceeds 200 kPa (29 psi).
S
Sharon MasseySep 3, 2025
Why is my Bredel Industrial Equipment leaking lubricant at the cover?
- V
  Victoria RossSep 3, 2025
  Lubricant leakage at the cover of your Bredel Industrial Equipment may be due to: * **Damaged seal ring:** The seal ring might be damaged and needs replacement. * **Incorrect torque:** The bolts may not be tightened to the specified torque. Tighten to the specified torque settings. Refer to § 11.1.6.
S
steven13Sep 7, 2025
What causes lubricant leakage at the bracket of my Bredel APEX35?
- S
  Sharon GatesSep 7, 2025
  If you notice lubricant leaking at the bracket of your Bredel Industrial Equipment, it could be due to: * **Hose blockage:** The hose might be blocked by an incompressible object. Remove the hose, check for blockages, and replace it if necessary. * **Loose bolts:** The bracket bolts may be loose. Tighten them to the specified torque settings. Refer to § 11.1.6.
R
ryan36Sep 10, 2025
What to do if there's leakage from the rear of the Bredel APEX35 Industrial Equipment pump housing "Buffer zone"?
- J
  jsmithSep 12, 2025
  If there is leakage from the rear of the pump housing "Buffer zone" of your Bredel Industrial Equipment, the likely cause is a damaged seal ring, which will need to be replaced.
L
Laura VelazquezNov 17, 2025
Why is my Bredel APEX35 Industrial Equipment pump temperature so high?
- A
  Amanda Carr PhDNov 17, 2025
  Several factors can cause a Bredel Industrial Equipment pump to overheat: * **Non-standard hose lubricant:** Using the wrong lubricant can lead to increased friction and heat. Consult your Bredel representative for the correct lubricant. * **Low lubricant level:** Insufficient lubrication increases friction. Add Bredel Genuine Hose Lubricant, referring to § 11.1.4 for the correct amount. * **Fluid temperature too high:** Exceeding the fluid's maximum temperature range can cause the pump to overheat. Consult your Bredel representative about the fluid's maximum temperature range. * **Internal friction:** Blocked or poor suction can cause internal friction. Check pipework/valves for blockages and ensure the suction pipework is short and adequately sized. * **High pump speed:** Oper...