Bridgeport GX 710 - Page 18

Page 18
KLUBER ISOFLEX NBU15
EVERY 600 HOURS
FREQUENCY
GREASE
POINTS
SERVICING
TYPE
LINEAR GUIDES BALL SCREW
MAS 403-1982
MACHINE DAMAGE
FAILURE TO US E P RO P ER T OO L HOL DER
MAY RESULT IN PERSONAL INJURY OR
OR MACHINE DAMAGE
MAY RESULT IN PERSONAL INJURY
FAILURE TO USE PR O PER S TUD
#40 BT TAPER TOOL HOLDERS
THIS MACHINE IS CONFIGURED TO USE
THAT CONF OR M T O J MTBA ST ANDARD
THIS MACHINE IS CONFIGURED TO
USE THE FOLLOWING TOOL STUD ONLY
TYPE: JMTBA STANDARD MAS 403-1982
P40T SPECIAL, METRIC THREADS
#40 BT TAPER, 45 DEGREE
MAS 403-1982
MACHINE DAMAGE
FAILURE TO USE PROPER TOOL HOLDER
MAY RESULT IN PERSONAL INJURY OR
OR MACHINE DAMAGE
MAY RESULT IN PERSONAL INJURY
FAILURE TO USE PROPER STUD
#40 BT TAPER TOOL HOLDERS
THIS MACHINE IS CONFIGURED TO USE
THAT CON FORM TO JMTBA ST ANDARD
THIS MACHINE IS CONFIGURED TO
USE THE FOLLOWING TOOL STUD ONLY
TYPE: J MTBA STANDA RD MAS 403-1982
P40T SPECIAL, METRIC THREADS
#40 BT TAPER, 45 DEGREE
TOOL RELEASE
TOOL RELEASE
MARRING SURFACE
CAREFULLY WASH
WITH SOFT CLEAN
AND DRY WINDOW
CLOTH TO AVOID
MARRING SURFACE
CAREFULLY WASH
WITH SOFT CLEAN
AND DRY WINDOW
CLOTH T O AVOID
MARRING SURFACE
CAREFULLY WASH
WITH SOFT CLEAN
AND DRY WINDOW
CLOTH TO AVOID
EXTERNAL DEVICE
POWER TO THE
BEFORE APPLYING
RS 232 CABLE
ALWAYS CONNECT
EXTERNAL DEVICE
POWER TO THE
BEFORE APPLYING
RS 232 CABLE
ALWAYS CONNECT
76¡Ó24mm2Kgf
DHz
F
76¡ Ó2
4mm
2Kgf
D
Hz
F
MACHINE WARRANTY
COVERED BY THE
HARDINGE INC.
"IMPORTANT"
ACCIDENT IS NOT
NEGLIGENCE, OR
FROM MISUSE,
DAMAGE RESULTING
MACHINE WARRANTY
COVERED BY THE
HARDINGE INC.
"IMPORTANT"
ACCIDENT IS NOT
NEGLIG ENCE , OR
FROM MISUSE,
DAMAGE RESULTING
Max Tool D iam e ter (m m ):
Max Part Capacity(mm):
Min Part Capacity(mm):
Max Spindle Speed(RPM):
Max Tool W eig ht (K g) :
+X -X
-Y
+Z
-Z
+Y
KLUBER ISOFLEX NBU15
EVERY 600 HOURSFREQUENCY
GREASE
POINTS
SERVICING
TYPE
LINEAR G U IDES BALL SCREW
GX 300 & GX 510 Front and right-side View
SUPPLY VOLTS
WIRING DIAGRAMS
THE OVER CU RREN T PR OTECTI VE DEVIC E
SHORT CIRCUIT INTERRUPTING CAPACITY OF
OVERCURRENT PROTECTION PROVIDED
AT MACHINE SUPPLY TERMINALS
NOTE - ADDITIONAL DATA PLATES IN CONTROL CASE
POWER
MODEL
KILOWATTS
CONTROL VO LTS
N/C
HERTZ
PHASE
MACHINE F L A
SPINDLE DRIVE
SUPPLY VOLTS
WIRING DIAGRAMS
THE OVERCURRENT PROTECTIVE DEVICE
SHORT CIRCUI T INTERRUPTING CAPACITY OF
OVERCURRENT PROTECTION PROVIDED
AT MACHINE SUPPLY TERMINALS
NOTE - ADDITIONAL DATA PL ATES IN CONTROL CASE
POWER
MODEL
KILOWATTS
CONTROL VOLTS
N/C
HERTZ
PHASE
MACHINE FLA
SPINDLE DRIVE
IF REQUIRED
MORE OFTEN
ONCE A WEEK
CLEAN FILTER
DO NOT BLOCK
AIR INLET
IF REQUIRED
MORE OFTEN
ONCE A WEEK
CLEAN FILTER
DO NOT BLOCK
AIR INLET
NV 001030368A
1
0
DOOR
INTERLOCK
FAX: +886-49-2252203
TEL: +886-49-2260536
MODEL
MFG.NO. DATE
4 Tzu Chiang 3rd Road, NanTou City, 540 Taiwan
WEIGHT KG
FAX: +886-49-2252203
TEL: +886-49-2260536
MODEL
MFG.NO.
DATE
4 Tzu Chiang 3rd Road, NanTou City, 540 Taiwan
WEIGHT KG
GX 300 & GX 510 Left-side and rear View