EasyManua.ls Logo

Briggs & Stratton 020498 - User Manual

Briggs & Stratton 020498
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Not for
Reproduction
Manual No. 317455 Revision B
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Pressure Washer
Operator’s Manual
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).

Table of Contents

Questions and Answers

  • M
    Mary DuncanAug 9, 2025
    Why won't my Briggs & Stratton 020498 engine start?
    • D
      David EvansAug 9, 2025
      Your Briggs & Stratton Pressure Washer engine might not start due to several reasons: * The oil level might be low, so fill the crankcase to the proper level. * The air cleaner could be dirty; clean or replace it. * The fuel tank might be empty; fill it with fuel. * The fuel could be stale; drain the tank and fill it with fresh fuel. * The spark plug wire may not be connected; connect it to the spark plug. * The spark plug might be bad; replace it. * There might be water in the fuel; drain the tank and fill it with fresh fuel.
  • D
    David JohnsonAug 16, 2025
    What to do if my Briggs & Stratton 020498 pump has no pressure?
    • M
      Melanie PhillipsAug 16, 2025
      If your Briggs & Stratton Pressure Washer pump isn't producing pressure, has erratic pressure, chatters, loses pressure, or has low water volume, consider the following: * If a low-pressure spray tip is installed, replace it with a high-pressure spray tip. * If the water inlet is blocked, clear it. * Ensure an adequate water supply. * If the inlet hose is kinked or leaking, straighten it or patch the leak. * Check and clean the inlet hose screen if it's clogged. * Ensure the water supply is not over 100°F (38º C); use a cooler water supply. * Clear any blockages in the high-pressure hose or replace if leaking. * Replace the spray gun if it leaks. * Clean the spray tip if it's obstructed.
  • C
    ccopelandAug 23, 2025
    Why is detergent not mixing with the spray in my Briggs & Stratton Pressure Washer?
    • A
      Anna GarciaAug 23, 2025
      If detergent fails to mix with the spray in your Briggs & Stratton Pressure Washer, check the following: * Ensure the detergent siphoning tube is submerged in the detergent. * Clean or replace the detergent siphoning tube if it's clogged or cracked. * Replace the high-pressure spray tip with a low-pressure spray tip. * Free the detergent siphoning check ball if it's stuck.
  • S
    stephanie74Aug 31, 2025
    Why is my Briggs & Stratton 020498 engine bogging down under load?
    • J
      Jennifer YoungSep 1, 2025
      If your Briggs & Stratton Pressure Washer engine runs well with no load but bogs down when a load is added, the engine speed might be too slow. Move the throttle control to the FAST position.

Summary

Operator Safety

General Safety Warnings

Critical safety alerts covering hazardous gases, chemical burns, and general hazards.

Operator Safety (Continued)

Fuel and Operational Safety

Warnings regarding fuel flammability, exhaust hazards, and safe operating practices.

High-Pressure Hazards

Risks associated with high-pressure water streams, including cuts and amputation.

Stability and Kickback Safety

Precautions for maintaining stability and handling kickback during operation.

Rotating Parts & Eye Protection

Safety measures for rotating components and the importance of eye protection.

Initial Setup and Fueling

Safe Fueling Procedures

Guidelines for safely adding gasoline, including fire prevention.

Connecting Water Supply

Hose Connections and Safety

Proper connection of hoses and safety precautions during water supply setup.

Pre-Start Checklist

Operation Guide

Location and CO Hazard Awareness

Importance of outdoor operation and carbon monoxide risk.

Starting the Pressure Washer

Step-by-step instructions for initiating the engine and pump.

Fire Safety Clearances Required

Operation Details

Throttle, Choke, and Starter Use

Startup Safety Precautions

Safety measures during engine startup, including kickback and eye protection.

Cleaning and Detergent Use

Applying Detergent Effectively

Steps for preparing and applying detergent solutions for cleaning.

Routine Maintenance

Maintenance Schedule Overview

Pre-Use Inspection Checklist

Engine and O-Ring Maintenance

Engine Oil Management

Recommendations, checking, adding, and changing engine oil.

Safety for Engine Servicing

Critical safety warnings when performing work on the engine.

System Care and Storage Prep

Post-Use Procedures

Steps to follow after each use to prepare the unit for storage.

Storage Recommendations

Winter Storage Protection

Methods to protect the unit from freezing temperatures during winter.

Long Term Storage Preparation

Steps for preparing the unit for storage longer than 30 days.

Pump Protection and Storage

Using PumpSaver or antifreeze to protect the pump during storage.

Troubleshooting Common Issues

Pump Performance Problems

Engine Performance Problems

Warranty Details

Limited Warranty Coverage

Warranty Exclusions and Limitations

Briggs & Stratton 020498 Specifications

General IconGeneral
Engine Displacement140 cc
Max Pressure2200 PSI
Flow Rate1.9 GPM
Hose Length25 ft
Pump TypeAxial Cam
Wheel Size10 in
Weight50 lb
Nozzle TypeQuick-Connect Tips

Related product manuals