Briggs & Stratton 1695979

Questions and Answers

T
Taylor FoxAug 13, 2025
Why Briggs & Stratton 1695979 engine fails to start?
- A
  Aaron KiddAug 13, 2025
  If your Briggs & Stratton Snow Blower engine won't start, there are several potential causes. Ensure the key is in the ON position. If the engine is cold, prime it by pressing the primer button twice before restarting. Check that the fuel shut-off valve, if equipped, is in the OPEN position. Make sure you have enough fuel in the tank. For a cold engine, ensure the choke is ON and the throttle is set to FAST. If the engine is flooded, move the choke to the OPEN/RUN position and the throttle to FAST, then crank the engine until it starts. If none of these steps work, there may be no spark, and you should consult an authorized dealer.
J
jason07Aug 16, 2025
Why Briggs & Stratton 1695979 engine starts hard or runs poorly?
- B
  Brittany LopezAug 16, 2025
  If your Briggs & Stratton Snow Blower engine starts hard or runs poorly, it could be due to several factors. One potential cause is water or old fuel in the tank. Drain the tank, dispose of the fuel at an authorized hazardous waste facility, and refill with fresh fuel. Another cause could be a faulty, fouled, or improperly gapped spark plug, which would require attention from an authorized dealer. Lastly, check if the fuel cap vent is blocked and clear it if necessary.
J
Juan GregoryAug 21, 2025
What to do if Briggs & Stratton Snow Blower has excessive vibration?
- T
  Teresa ShepherdAug 21, 2025
  If your Briggs & Stratton Snow Blower is vibrating excessively, stop the engine immediately and tighten all hardware. If the vibration continues, it could be due to loose parts or a damaged impeller. In this case, have the unit serviced by an authorized dealer.
P
perezkimberlyAug 28, 2025
Why Briggs & Stratton 1695979 Snow Blower unit fails to propel itself?
- J
  Janet RhodesAug 28, 2025
  If your Briggs & Stratton Snow Blower unit fails to propel itself, it could be due to a loose or damaged drive belt, which would need replacement by an authorized dealer. Another possible cause is an incorrect adjustment of the traction drive cable, also requiring attention from an authorized dealer. Lastly, a worn or damaged friction disc could be the issue, necessitating replacement by an authorized dealer.
C
Cory GriffinSep 1, 2025
What to do if discharge chute or deflector does not work on Briggs & Stratton 1695979 Snow Blower?
- M
  Melissa GreenSep 1, 2025
  If the discharge chute or deflector on your Briggs & Stratton Snow Blower does not work, it may be out of adjustment or need lubrication. Adjust and/or lubricate the control linkage to resolve this issue.
B
Brent OwenSep 4, 2025
Why Briggs & Stratton 1695979 Snow Blower auger does not stop after releasing control lever?
- W
  William JohnsonSep 5, 2025
  If the auger on your Briggs & Stratton Snow Blower does not stop within 5 seconds after releasing the right control lever, it could be because the Free Hand control (if equipped) is ACTIVE. Release both the auger control and the Free Hand control to stop the auger. Alternatively, the auger drive belt or auger belt guide may be out of adjustment, requiring service from an authorized dealer.
K
Karen HudsonSep 8, 2025
How to adjust scraper bar on Briggs & Stratton 1695979?
- K
  Katie EscobarSep 8, 2025
  If the scraper bar on your Briggs & Stratton Snow Blower does not clean the hard surface properly, it is likely that the skid shoes and scraper bar are improperly adjusted. Raise or lower the skid shoes and scraper bar to correct this.
L
Lisa StevensNov 23, 2025
What to do if Briggs & Stratton 1695979 Snow Blower unit fails to discharge snow?
- C
  Craig DominguezNov 23, 2025
  If your Briggs & Stratton Snow Blower unit fails to discharge snow, there are several possible reasons. It could be due to a loose or damaged auger drive belt, which would require you to see an authorized dealer. The auger control cable might not be adjusted correctly; in this case, adjust the auger control cable, referring to the Maintenance section of this manual. A broken shear pin or shear bolt could also be the cause; replace it, referring to the Maintenance section of this manual, or see an authorized dealer. The discharge chute could be clogged; stop the engine immediately and use the clean-out tool to clear it, cleaning both the chute and the inside of the auger housing. Finally, a foreign object might be lodged in the auger; stop the engine immediately and use the clean-out tool t...

Briggs & Stratton 1695979 Specifications

General

Engine Displacement (cc)	208
Clearing Width (in)	24
Intake Height (in)	20
Fuel Tank Capacity (gal)	0.8
Oil Capacity (oz)	20
Start Type	Electric/Recoil
Speed Settings	6 Forward / 2 Reverse
Auger Type	Steel