Briggs & Stratton ELITE 09801

Questions and Answers

A
adamcurrySep 19, 2025
Why does my Briggs & Stratton ELITE 09801 Portable Generator bog down when I connect a load?
- K
  kfitzgeraldSep 19, 2025
  If your Briggs & Stratton Portable Generator runs well without a load but bogs down when loads are connected, consider these potential issues: 1. A short circuit in a connected load. Disconnect the shorted electrical load. 2. The generator is overloaded. See the section on avoiding generator overload. 3. A clogged or dirty fuel filter. Clean or replace the fuel filter.
J
Jesse WeissAug 25, 2025
What to do if detergent fails to mix with spray in my Briggs & Stratton Pressure Washer?
- M
  Mary JenkinsAug 25, 2025
  If detergent isn't mixing with the spray from your Briggs & Stratton Pressure Washer, consider the following: 1. Ensure the detergent siphoning tube is fully submerged in the detergent. 2. Clean or replace the chemical filter or detergent siphoning tube if it's clogged or cracked. 3. Replace the spray tip with a low-pressure spray tip if a high-pressure one is currently installed.
L
Lindsey DuncanAug 26, 2025
Why won't my Briggs & Stratton ELITE 09801 Portable Generator start, or why does it start and run rough?
- J
  Jerry JamesAug 26, 2025
  If your Briggs & Stratton Portable Generator won't start or runs rough, consider these potential causes: 1. A failed battery might be the reason. If so, replace the battery. 2. The oil level might be too low. In this case, fill the crankcase to the proper level or place the generator on a level surface.
S
Susan HernandezAug 27, 2025
How to fix a Briggs & Stratton ELITE 09801 Portable Generator that will not start or starts and runs rough?
- A
  Andrew GonzalezAug 27, 2025
  If your Briggs & Stratton Portable Generator won't start or runs roughly, there are a couple of things to check. The battery might be failed, so replace battery. Also, the oil level could be low, so fill the crankcase to the proper level or place the generator on a level surface.
D
Dr. Janice LeonardSep 23, 2025
What causes a Briggs & Stratton ELITE 09801 to shut down while running?
- D
  Debra JacksonSep 23, 2025
  Your Briggs & Stratton Portable Generator might shut down while running due to: * Being out of fuel: Fill the fuel tank. * A clogged or dirty fuel filter: Clean or replace the fuel filter. * Low oil level: Fill the crankcase to the proper level or place the generator on a level surface.
D
Dr. Andrew Hamilton MDSep 23, 2025
Why does my Briggs & Stratton Portable Generator engine lack power?
- C
  Cynthia WashingtonSep 23, 2025
  If your Briggs & Stratton Portable Generator engine lacks power, it might be because: * The load is too high. Refer to the instructions on how to avoid overloading the generator. * The air filter is dirty. Replace the air filter. * The fuel filter is clogged or dirty. Clean or replace the fuel filter.
L
Lisa LutzSep 10, 2025
What to do if Briggs & Stratton Air Compressor Safety Valve pops off?
- J
  Joshua GomezSep 12, 2025
  If the Safety Valve on your Briggs & Stratton Air Compressor is popping off due to excessive tank pressure, move the engine ON/OFF Switch to the OFF position and contact a trained service technician.
E
Elizabeth FloresSep 12, 2025
What to do if my Briggs & Stratton ELITE 09801 shuts down during operation?
- S
  Stephen HinesSep 12, 2025
  If your Briggs & Stratton Portable Generator shuts down during operation, there are a couple of things to check: * Make sure you have enough gasoline by filling the fuel tank. * Check the oil level and fill the crankcase to the proper level, or place the generator on a level surface.
T
Tracie WalkerSep 3, 2025
Why is my Briggs & Stratton Air Compressor losing air?
- L
  Laura DavisSep 3, 2025
  Air losses in your Briggs & Stratton Air Compressor can stem from several causes: 1. A cracked fitting. In this case, tighten the fittings where you hear air escaping, or replace the fittings. 2. A dirty or damaged check valve seat. If so, replace the check valve and contact a trained service technician. 3. A defective pressure switch release valve. Contact a trained service technician. 4. A defective air tank. The air tank must be replaced; do not attempt to repair it. 5. A leaking seal. Contact a trained service technician. 6. A damaged regulator. Contact a trained service technician.
S
Sarah WillisSep 1, 2025
Why does my Briggs & Stratton Pressure Washer pump have low or erratic pressure?
- H
  Hunter BaileySep 1, 2025
  If your Briggs & Stratton Pressure Washer pump isn't producing pressure, has erratic pressure, chatters, loses pressure, or has low water volume, here's what to check: 1. Ensure a high-pressure spray tip is installed; if not, replace it. 2. Clear any blockage in the water inlet. 3. Make sure the water supply is adequate. 4. Straighten any kinks in the inlet hose and patch any leaks. 5. Check and clean the inlet hose strainer. 6. Ensure the water supply is not over 100°F; use a cooler water supply. 7. Clear any blockages in the high-pressure hose. 8. Replace the gun if it's leaking. 9. Clean any obstructions in the spray tip. 10. If none of these steps work, the pump may be faulty, consider contacting an authorized service facility.