To Next PageTo Next PageHow to fix a Briggs & Stratton Pressure Washer engine that bogs down under load?
If your Briggs & Stratton Pressure Washer engine runs well with no load but bogs down when a load is added, the engine speed may be too slow. Try moving the throttle control to the FAST position. If the engine still bogs down, contact a Briggs and Stratton service facility.
Why is my Briggs & Stratton Pressure Washer pump losing pressure?
Several factors can cause your Briggs & Stratton Pressure Washer pump to lose pressure, produce erratic pressure, or have low water volume. The issue might be a low-pressure spray tip installed (replace with a high-pressure tip), a blocked water inlet (clear it), an inadequate water supply (ensure adequate flow), a kinked or leaking inlet hose (straighten or patch it), a clogged inlet hose strainer (check and clean it), a water supply over 100°F (use a cooler supply), a blocked or leaking high-pressure hose (clear any blockages), a leaking gun (replace it), or an obstructed nozzle (clean it). If none of these resolve the issue, the pump may be faulty, and you should contact a Briggs & Stratton Power Products service facility.
How to fix a Briggs & Stratton ELITE 09801 that will not start?
If your Briggs & Stratton Portable Generator engine won't start or runs rough, possible causes include: * The Run/Stop switch is in the "Stop" position: Set the switch to "Run". * The fuel valve is in the "Off" position: Turn the fuel valve to the "On" position. * Low oil level: Fill the crankcase to the proper level or place the generator on a level surface. * Out of fuel: Fill the fuel tank. * Stale fuel or water in fuel: Drain the fuel tank and carburetor, then fill with fresh fuel. * Spark plug wire not connected: Connect the wire to the spark plug. * Bad spark plug: Replace the spark plug. * Dirty air cleaner or fuel filter: Clean or replace them. * Failed battery: Replace battery. * Flooded engine: Wait 5 minutes and re-crank the engine.
How to troubleshoot a Briggs & Stratton Portable Generator that will not start or starts and runs rough?
If your Briggs & Stratton Portable Generator won't start or starts and runs roughly, there are a couple of things to check. First, make sure the fuel valve is in the "On" position. If that's not the issue, the battery may have failed, in which case you should replace it.
How to fix a Briggs & Stratton ELITE 09801 Portable Generator that will not start or starts and runs rough?
If your Briggs & Stratton Portable Generator won't start or runs roughly, there are a couple of things to check. The battery might be failed, so replace battery. Also, the oil level could be low, so fill the crankcase to the proper level or place the generator on a level surface.
Why won't my Briggs & Stratton ELITE 09801 Portable Generator start, or why does it start and run rough?
If your Briggs & Stratton Portable Generator won't start or runs rough, consider these potential causes: 1. A failed battery might be the reason. If so, replace the battery. 2. The oil level might be too low. In this case, fill the crankcase to the proper level or place the generator on a level surface.
What to do if detergent doesn't mix with spray in my Briggs & Stratton Pressure Washer?
If the detergent is not mixing with the spray in your Briggs & Stratton Pressure Washer, there are a few things you can check. First, make sure the chemical shut-off valves are in the “On” position. Rotate the chemical shut-off valve on the desired chemical reservoir to the “On” position. Also, check the in-line filter. Finally, ensure that you have a low-pressure spray tip installed instead of a high-pressure one; if not, replace it.
What to do if Briggs & Stratton Air Compressor Safety Valve pops off?
General| Type | Portable Generator |
|---|---|
| Engine Displacement | 420 cc |
| Fuel Type | Gasoline |
| Engine | Briggs & Stratton |
| Outlet Types | 4x 120V 20A, 1x 120/240V 30A |
| Noise Level | 74 dB |
