Briggs & Stratton WP2-35 User Manual

152 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Water Pump

Operator’s Manual

Bomba de agua

Manual del Operario

Bomba de Água

Manual do Operador

Pompe à eau

Manuel d’utilisation

Pompa wodna

Instrukcja obsługi

Vesipumppu

Ohjekirja

Водяной насос

Руководство по эксплуатации

Su Pompası

Kullanma Kılavuzu

Original Instruction

Appearance may vary slightly

MS10408 (REV. -)

WP20, WP2-35, WP30

en

es

pt

fr

pl

fi

ru

tr

pt

Português

fi

Suomi

Table of Contents

Other manuals for Briggs & Stratton WP2-35

Manual220 pages

Questions and Answers:

S
Samuel EvansAug 6, 2025
Why Briggs & Stratton WP2-35 Water Pump engine won't start?
- C
  Casey Merritt DDSAug 6, 2025
  If your Briggs & Stratton Water Pump engine won't start, lacks power, runs rough, or falters, consider these potential causes: Ensure the rocker switch is set to 'On' and the fuel shutoff is in the 'On' position. Check the air cleaner and clean or replace it if dirty. Make sure there's fuel in the tank; if empty, wait two minutes before refueling. Drain the fuel tank and carburetor and refill with fresh fuel if the current fuel is stale or contaminated. Verify the spark plug wire is connected, and replace the spark plug if it’s bad. If the engine is flooded, wait 5 minutes and try re-cranking.
J
Judy EllisAug 21, 2025
What to do if my Briggs & Stratton Water Pump has low output?
- J
  James WilliamsAug 21, 2025
  If your Briggs & Stratton Water Pump has low output, several factors could be responsible. First, ensure the pump is correctly primed by filling the pump chamber with water. Check the suction hose for restrictions, collapse, damage, or excessive length, and replace it if necessary. Make sure the strainer is fully submerged. Inspect the suction hose connector for air leaks, replacing the sealing washer and tightening the connector and clamp if needed. Clean any debris from the strainer. Verify that the discharge hose isn't restricted, damaged, or too long, replacing it if needed. Reduce the head by relocating the pump or hoses. Finally, ensure the engine speed lever is in the 'Fast' position.

Briggs & Stratton WP2-35 Specifications

General

Max Head	115 ft
Type	Centrifugal
Suction Lift	25 ft
Engine Type	4-stroke OHV
Inlet Size	2 inch
Outlet Size	2 inch
Engine	Briggs & Stratton

Summary

Important Safety Instructions

Safety Symbols and Meanings

Explains the safety alert symbol, signal words, and hazard symbols used in the manual.

Hazard Symbols and Meanings

Illustrates and defines symbols for hazards like explosion, fire, electric shock, toxic fumes, and hot surfaces.

Assembly

Add Engine Oil

Operation

Safe Operating Considerations

Advice on clearances, air movement, and avoiding exhaust gas accumulation.

Operational Procedures

Prime the Water Pump

Step-by-step instructions for filling and priming the water pump before starting.

Strainer Basket Placement

Instructions for placing the strainer basket into the water source to prevent debris intake.

Starting the Water Pump

Detailed steps for starting the engine, including choke and throttle settings.

Stopping and Draining the Pump

Stopping the Water Pump

Procedures for safely shutting down the engine and fuel supply.

Drain and Flush Water Pump

Instructions for draining hoses and flushing internal components for maintenance or storage.

Maintenance

Maintenance Schedule and Recommendations

Engine Maintenance

Oil Recommendations and Checks

Changing Engine Oil

Troubleshooting

Pump Output Issues

Addresses problems with no or low pump output and their potential causes and corrections.

Engine Starting and Running Problems

Solutions for engine not starting, lacking power, or running rough.

Engine Shutdown Issues

Related product manuals

Preview: Briggs & Stratton WP20

Briggs & Stratton WP20

Preview: Water Transfer Pump

Water Transfer Pump