EasyManua.ls Logo

Broan rmdd3004 - User Manual

Broan rmdd3004
40 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Downdraft Ventilators
Page 1
WARNING
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer at the address or telephone
number in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from be-
ing switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guideline
and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fire, use only metal ductwork.
8. Do not install this product with the activating switch directly behind
a burner or element. Minimum distance between the switch and the
edge of the burner should be 4 inches.
9. Loose-fitting or hanging clothing should never be worn when operating
this appliance. They may be ignited by burners/elements on cooktop.
10. Children should not be left alone or unattended in the area where this
appliance is in use.
11. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
cooking flaming foods.
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING
a
:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immedi
ately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels
- a violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you
already know how to operate it.
B. The fire is small and contained in the area where it
started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
a
Based on “Kitchen Firesafety Tips” published by NFPA.
MODEL WIDTH BLOWER
RMDD3004 30" 500 cfm Internal
RMDD3604 36" 500 cfm Internal
RMDD4804 48" 500 cfm Internal
RMDD3004EX 30" Models 331H, 332H, 335, 336 HLB3, HLB6, HLB9, and HLB11 External (purchase separately)
RMDD3604EX 36" Models 331H, 332H, 335, 336 HLB3, HLB6, HLB9, and HLB11 External (purchase separately)
RMDD4804EX 48" Models 331H, 332H, 335, 336 HLB3, HLB6, HLB9, and HLB11 External (purchase separately)
WARNING - To reduce the risk of burns or ignition of clothing by reaching across burners, the downdraft remote control MUST
be mounted in the countertop - at least 4" from the burners. See "INSTALL COOKTOP" section on page 8.
!
INSTALLER:
Save this manual for Electrical
Inspector and Homeowner to use.
NOTE: Model RMDDRBK Remote Up/Down
Control sold separately.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced impel-
lers, keep drywall spray, construction dust, etc. off power unit.
4. Clean filters and grease-laden surfaces frequently.
5. Do not repair or replace any part of this appliance unless specifically
recommended in this manual. All other servicing should be done by
a qualified technician.
6. Please read specification label on product for further information and
requirements.
7. To reduce the risk of fire and electric shock, install this downdraft only
with Rangemaster blower models shown below. Other blowers cannot
be substituted. (blowers sold separately).
MODEL WIDTH BLOWER
RMDD3004 30" 500 cfm Internal
RMDD3604 36" 500 cfm Internal
RMDD4804 48" 500 cfm Internal
RMDD3004EX 30" External, Model 331H, 332H, 335, 336,
HLB3, HLB6, HLB9, y HLB11 (purchase
separately)
RMDD3604EX 36" External, Model 331H, 332H, 335, 336,
HLB3, HLB6, HLB9, y HLB11 (purchase
separately)
RMDD4804EX 48" External, Model 331H, 332H, 335, 336,
HLB3, HLB6, HLB9, y HLB11 (purchase
separately)
Register your product online at: www.broan.com/register
Question and Answer IconNeed help?

Do you have a question about the Broan rmdd3004 and is the answer not in the manual?

Summary

READ AND SAVE THESE INSTRUCTIONS

General Safety Warnings

Instructions to reduce risk of fire, electric shock, or injury to persons.

Range Top Grease Fire Safety

Guidelines to prevent cooking fires and ensure safe operation.

Grease Fire Injury Prevention

Steps to take to reduce injury risk during range top grease fires.

Cautionary Notes

Important usage precautions and warnings for safe operation.

PLANNING

Internal Blower Installation

Basic steps for installing the internal blower system.

External Blower Installation

Basic steps for installing the external blower system.

TAKE MEASUREMENTS

All Units Measurement Guidelines

Measurement considerations for cooktop, countertop, and cabinet fit.

PLAN THE DUCTWORK

Internal Blower Ductwork

Ductwork options and equivalent length calculations for internal blowers.

External Blower Ductwork

Ductwork options and equivalent length calculations for external blowers.

PLAN THE CABINET CUTOUTS

Left Side Discharge Cutout

Dimensions and placement for left side duct discharge cutout.

Bottom Discharge Cutout

Dimensions and placement for bottom duct discharge cutout.

Right Side Discharge Cutout

Dimensions and placement for right side duct discharge cutout.

PLAN THE WIRING

Internal Blower Wiring

Electrical outlet location and circuit requirements for internal blowers.

External Blower Wiring

Electrical outlet location and circuit requirements for external blowers.

PREPARE THE DOWNDRAFT

Blower Duct Connection

Procedure for orienting and connecting the blower to ductwork.

CUT COUNTERTOP OPENING

All Units Opening Procedure

Steps for accurately cutting the countertop opening for the downdraft.

MOUNT THE UNIT

All Units Mounting Instructions

How to set and secure the downdraft unit in the cabinet.

INSTALL DUCTWORK

Blower Installation Ductwork

Connecting the ductwork to the blower and cabinet.

INSTALL ELECTRICAL WIRING

Internal Blower Electrical Wiring

Steps for connecting the power supply to internal blower systems.

External Blower Electrical Wiring

Steps for connecting the power supply to external blower systems.

INSTALL COOKTOP

All Units Cooktop Installation

Procedure for aligning and securing the cooktop with the downdraft.

REMOTE UP;DOWN CONTROL INSTALLATION

Optional Remote Control Setup

Instructions for installing the optional remote control unit.

USE AND CARE

General Use and Care

Guidance on operating the downdraft and general maintenance.

Cleaning Instructions

How to clean filters and the unit safely and effectively.

Servicing the Unit

Steps for accessing and servicing internal components.

OPERATION

Basic Operation

How to turn the downdraft on/off and adjust fan speed.

Heat Sentry Feature

Explanation of the automatic speed adjustment based on temperature.

WIRING DIAGRAM

System Wiring Diagram

Schematic showing electrical connections for the downdraft system.

WARRANTY INFORMATION

Broan One Year Limited Warranty

Details of the product's limited warranty coverage and terms.

SERVICE PARTS LISTING

Parts by Width and Description

List of replacement parts categorized by model width and description.

SERVICE PARTS DIAGRAM

Component Identification

Visual identification of replacement parts using numbered diagrams.

Broan rmdd3004 Specifications

General IconGeneral
Colorstainless steel
Venting Typeducted
Blower Typeinternal
CFM600 cfm
Duct Size3 1/4" x 10"
Control Typevariable speed; rotary
Interior Lightn/a
Voltage120 volts
Current15; 4.0
Weight and Dimensions IconWeight and Dimensions
Depth7 inch
Height29 1/2 inch
Width30 inch

Related product manuals