Brother CS10 - User Manual

Questions and Answers

V
Vanessa ReynoldsAug 17, 2025
Why is my Brother CS10 not working?
- C
  Christopher RiversAug 17, 2025
  There are several possible reasons why your Brother Sewing Machine might not be working: * The machine might not be plugged in, so ensure it is properly connected to a power source. * The main power switch could be turned off, so turn it on. * The bobbin winder shaft may be pushed to the right; move it to the left. * You might not be using the foot controller properly; make sure you are using it correctly.
S
Shannon RodriguezAug 20, 2025
How to fix skipped stitches on my Brother CS10?
- G
  Glenn PhelpsAug 20, 2025
  If you're experiencing skipped stitches on your Brother Sewing Machine, try these solutions: * Correct the upper threading. * Use the right combination of fabric, thread, and needle. * Replace the needle if it's bent or blunt. * Insert the needle properly. * Remove the needle plate cover and clean the plate and the bobbin case to eliminate accumulated dust.
P
Paul BaileyAug 22, 2025
How to adjust thread tension on Brother Sewing Machine?
- L
  linda67Aug 22, 2025
  If the thread tension is incorrect on your Brother Sewing Machine, consider the following: * Correct the upper threading. * Wind the bobbin thread properly. * Use the right combination of thread and needle for the fabric you are using. * Attach the presser-foot holder properly. * Adjust the tension of the upper thread. * Use only a bobbin that has been designed for this machine. * Reset the bobbin thread correctly.
K
kimberly06Aug 26, 2025
Why does the needle keep breaking on my Brother Sewing Machine?
- C
  carl79Aug 26, 2025
  If the needle on your Brother Sewing Machine breaks, consider the following: * Ensure the needle is fitted properly. * Tighten the needle clamp screw firmly with a screwdriver. * Replace the needle if it is bent or blunt. * Use the correct combination of fabric, thread, and needle. * Attach the appropriate presser foot for the stitch type. * Loosen the upper thread tension if it's too tight. * Lightly guide the fabric instead of pulling it.
M
Matthew SimmonsAug 28, 2025
Why does the upper thread break on my Brother CS10 Sewing Machine?
- S
  shelby98Aug 28, 2025
  If the upper thread keeps breaking on your Brother Sewing Machine, here are a few things to check: * Make sure you've threaded the upper thread correctly. * Remove any knots or tangles in the thread. * Ensure the needle is appropriate for the thread you're using. * Loosen the upper thread tension if it's too tight. * Remove any tangled thread, especially from the bobbin case, and clean the bobbin case if necessary. * Replace the needle if it's bent or blunt.
P
Patricia JonesAug 30, 2025
What to do if the lower thread is tangled in my Brother Sewing Machine?
- K
  Kenneth SmithAug 31, 2025
  If the lower thread is tangling or breaking on your Brother Sewing Machine, try these solutions: * Wind the bobbin thread properly. * Replace the bobbin if it's scratched or doesn't turn smoothly. * Remove any tangled thread and clean the bobbin case. * Use only bobbins designed for your machine. * Reset the bobbin thread correctly.
K
Kevin HunterSep 2, 2025
Why is the fabric not feeding through my Brother CS10 Sewing Machine?
- J
  Jasmine JohnsonSep 2, 2025
  If the fabric does not feed through your Brother Sewing Machine, it could be due to: * The feed dogs being lowered; slide the feed dog position lever to the correct position. * The stitch being too fine; lengthen the stitch length. * Using the wrong combination of fabric, thread, and needle; choose the appropriate combination. * Thread tangled in the bobbin case; remove the tangled thread and clean the bobbin case.
M
Mark WilliamsSep 5, 2025
What to do if the stitch is not sewn correctly on my Brother CS10?
- C
  Christine WilliamsSep 5, 2025
  If the stitch isn't sewn correctly on your Brother Sewing Machine, it might be because: * The presser foot you're using isn't correct for the type of stitch; attach the correct presser foot. * The thread tension is incorrect; adjust the tension of the upper thread. * The thread is tangled, for example, in the bobbin case; remove the tangled thread and clean the bobbin case.
R
Ryan OneillSep 8, 2025
Why is the fabric wrinkled when I sew with my Brother Sewing Machine?
- P
  Patrick GrantSep 8, 2025
  If the fabric is wrinkling while using your Brother Sewing Machine, consider the following: * Ensure you've threaded the upper thread and wound the bobbin thread correctly. * Fit the spool properly. * Use the right combination of fabric, thread, and needle. * Replace the needle if it is bent or blunt. * If sewing thin fabric, use a stabilizer material under the fabric. * Adjust the tension of the upper thread.
L
Lisa ArroyoSep 12, 2025
Why is my Brother CS10 making a high pitched noise?
- P
  Patricia SandersSep 12, 2025
  If you're hearing a high-pitched noise while sewing with your Brother Sewing Machine, it could be due to: * Dust buildup in the feed dogs or bobbin case – clean the bobbin case. * Incorrect upper threading – correct the upper threading. * A scratched bobbin case – consider replacing it. * Using the wrong bobbin – use only bobbins designed for your machine.

Brother CS10 Specifications

General

Stitch Number	40
Buttonhole Styles	5
Needle Positions	Variable
Display	LCD
Needle Threader	Yes
Maximum Stitch Length	4 mm
Maximum Stitch Width	5 mm
Bobbin	Top drop-in bobbin